9VAC5-40 Existing Stationary Sources (Rev. J07) , Virginia Register

Agency Contact: Gary Graham, Department of Environmental Quality, 629 East Main Street, P.O. Box 1105, Richmond, VA 23218, telephone (804) 698-4103, FAX (804) 698-4510, or email gary.graham@deq.virginia.gov.

A new chapter (9VAC5-45, Consumer and Commercial Products) was originally proposed as part of this regulatory action, consisting of general requirements and seven articles to control volatile organic compound (VOC) emissions from several types of consumer and commercial products in the Northern Virginia, Fredericksburg, and Richmond VOC Emissions Control Areas. By separate regulatory action published in 26:12 VA.R. 1876-1978 February 15, 2010, the new chapter became an effective regulation on March 17, 2010, but it is applicable only in the Northern Virginia and Fredericksburg VOC Emission Control Areas. As previously proposed, this regulatory action is revised to include only those provisions that represent changes to the new effective regulation.

The amendments apply the provisions of four of the original articles in the Richmond VOC Emissions Control Area; specifically, provisions pertaining to portable fuel containers manufactured on or after August 1, 2010; consumer and commercial products manufactured on or after August 1, 2010; architectural and industrial maintenance coatings; and adhesives, adhesive primers, sealants, and sealant primers. Additionally, Article 48 of Chapter 40 (9VAC5-40) is amended to apply provisions pertaining to mobile equipment repair and refinishing operations in the Richmond VOC Emissions Control Area.

Compliance dates for standards applicable in the Richmond VOC Emissions Control Area have been changed to a more reasonable date in the future. The compliance dates for a proposed phase-in of standards applicable to the use of single-ply roof membrane adhesives and sealants has been modified to include a separate compliance date for the phase-in in the Richmond VOC Emissions Control Area. A temporary exemption for the manufacture and distribution of single-ply roof membrane adhesives and sealants, which did not appear in the original proposal but already appears in the effective regulatory language, has been preserved.

Summary of Public Comments and Agency's Response: A summary of comments made by the public and the agency's response may be obtained from the promulgating agency or viewed at the office of the Registrar of Regulations.

Article 48
Emission Standards for Mobile Equipment Repair and Refinishing Operations (Rule 4-48)

A. Except as provided in ~~subsection C of this section~~ 9VAC5-40-6975, the affected facility to which the provisions of this article apply is each mobile equipment repair and refinishing operation. Certain provisions also apply to each person providing or selling affected coatings.

B. The provisions of this article apply only to sources and persons in the Northern Virginia, ~~and~~ Fredericksburg, and Richmond Volatile Organic Compound Emissions Control Areas designated in 9VAC5-20-206.

~~C. The provisions of this article do not apply under any of the following circumstances:~~

1. The mobile equipment repair and refinishing operation is subject to Article 28 (9VAC5-40-3860 et seq.) of 9VAC5 Chapter 40 (Emission Standards for Automobile and Light Duty Truck Coating Application Systems).

2. The mobile equipment repair and refinishing operation is subject to Article 34 (9VAC5-40-4760 et seq.) of 9VAC5 Chapter 40 (Emission Standards for Miscellaneous Metal Parts and Products Coating Application Systems).

~~3. The person applying the coatings does not receive compensation for the application of the coatings.~~

4. The mobile equipment repair and refinishing operations uses coatings required to meet military specifications (MILSPEC) where no other existing coating can be used that meets the provisions of this article.

The provisions of this article do not apply under any of the following circumstances:

1. The mobile equipment repair and refinishing operation is subject to Article 28 (9VAC5-40-3860 et seq.) of 9VAC5-40 (Emission Standards for Automobile and Light Duty Truck Coating Application Systems).

2. The mobile equipment repair and refinishing operation is subject to Article 34 (9VAC5-40-4760 et seq.) of 9VAC5-40 (Emission Standards for Miscellaneous Metal Parts and Products Coating Application Systems).

3. The person applying the coatings does not receive compensation for the application of the coatings.

4. The mobile equipment repair and refinishing operation uses coatings required to meet military specifications (MILSPEC) where no other existing coating can be used that meets the provisions of this article.

Affected persons and facilities shall comply with the provisions of this article as expeditiously as possible but in no case later than:

3. [ ~~May 1, 2010~~ March 1, 2014 ], in the Richmond VOC Emissions Control Area.

Article 1
Emission Standards for Portable Fuel Containers and Spouts Manufactured before [ ~~May 1, 2010~~ ] August 1, 2010

A. Except as provided in 9VAC5-45-70, the provisions of this article apply to any portable fuel container or spout manufactured before [ ~~May 1, 2010~~ ] August 1, 2010. The provisions of Article 2 (9VAC5-45-160 et seq.) of this part apply to portable fuel containers and spouts manufactured on or after [ ~~May 1, 2010~~ ] August 1, 2010.

B. Except as provided in 9VAC5-45-70, the provisions of this article apply to any owner or other person who sells, supplies, offers for sale, or manufactures for sale portable fuel containers or spouts.

C. The provisions of this article apply only to owners and other persons in the Northern Virginia and Fredericksburg Volatile Organic Compound Emissions Control Areas designated in 9VAC5-20-206.

A. The provisions of this article do not apply to any portable fuel container or spout manufactured for shipment, sale, and use outside of the applicable volatile organic compound emissions control areas designated in 9VAC5-45-60.

B. The provisions of this article do not apply to a manufacturer or distributor who sells, supplies, or offers for sale a portable fuel container or spout that does not comply with the emission standards specified in 9VAC5-45-90, as long as the manufacturer or distributor can demonstrate that: (i) the portable fuel container or spout is intended for shipment and use outside of the applicable volatile organic compound emissions control areas designated in 9VAC5-45-60 C; and (ii) the manufacturer or distributor has taken reasonable prudent precautions to assure that the portable fuel container or spout is not distributed within the applicable volatile organic compound emissions control areas designated in 9VAC5-45-60 C. This subsection does not apply to portable fuel containers or spouts that are sold, supplied, or offered for sale to retail outlets.

C. The provisions of this article do not apply to safety cans meeting the requirements of ~~subpart F of~~ 29 CFR Part 1926 Subpart F.

D. The provisions of this article do not apply to portable fuel containers with a nominal capacity less than or equal to one quart.

E. The provisions of this article do not apply to rapid refueling devices with nominal capacities greater than or equal to four gallons, provided (i) such devices are designed for use in officially sanctioned off-highway motor sports such as car racing or motorcycle competitions, and (ii) such devices either create a leak-proof seal against a stock target fuel tank, or are designed to operate in conjunction with a receiver permanently installed on the target fuel tank.

F. The provisions of this article do not apply to portable fuel tanks manufactured specifically to deliver fuel through a hose attached between the portable fuel tank and the outboard engine for the purpose of operating the outboard engine.

G. The provisions of this article do not apply to closed-system portable fuel containers that are used exclusively for fueling remote control model airplanes.

H. For purposes of this article, the terms "supply" or "supplied" do not include internal transactions within a business or governmental entity. These terms only apply to transactions between manufacturers/commercial distributors that sell, or otherwise provide, products to businesses/governmental entities/individuals.

A. No owner or other person shall sell, supply, offer for sale, or manufacture for sale any portable fuel container after the compliance dates specified in 9VAC5-45-120 A unless that portable fuel container meets all of the following standards for spill-proof systems:

1. Has an automatic shut-off that stops the fuel flow before the target fuel tank overflows.

2. Automatically closes and seals when removed from the target fuel tank and remains completely closed when not dispensing fuel.

5. Is warranted by the manufacturer for a period of not less than one year against defects in materials and workmanship.

B. No owner or other person shall sell, supply, offer for sale, or manufacture for sale any spout after the compliance dates specified in 9VAC5-45-120 unless that spout meets all of the following standards for spill-proof spouts:

1. Has an automatic shut-off that stops the fuel flow before the target fuel tank overflows.

2. Automatically closes and seals when removed from the target fuel tank and remains completely closed when not dispensing fuel.

3. Is warranted by the manufacturer for a period of not less than one year against defects in materials and workmanship.

C. The test procedures for determining compliance with the standards in this section are set forth in 9VAC5-45-130. The manufacturer of portable fuel containers or spouts shall perform the tests for determining compliance as set forth in 9VAC5-45-130 to show that its product meets the standards of this section prior to allowing the product to be offered for sale. The manufacturer shall maintain records of these compliance tests for as long as the product is available for sale and shall make those test results available within 60 days of request.

D. Compliance with the standards in this section does not exempt spill-proof systems or spill-proof spouts from compliance with other applicable federal and state statutes and regulations such as state fire codes, safety codes, and other safety regulations, nor will the board test for or determine compliance with such other statutes or regulations.

E. The following provisions apply to sell through of portable fuel containers and spouts manufactured before [ ~~May 1, 2010~~ ] August 1, 2010:

1. Notwithstanding the provisions of subsections A and B of this section, a portable fuel container or spout manufactured before the applicable compliance date specified in 9VAC5-45-120 A, may be sold, supplied, or offered for sale after the applicable compliance date, if the date of manufacture or a date code representing the date of manufacture is clearly displayed on the portable fuel container or spout.

2. Notwithstanding the provisions of subsections A and B of this section, a portable fuel container or spout manufactured after the applicable compliance date specified in 9VAC5-45-120 A and before [ ~~May 1, 2010~~ ] August 1, 2010, may be sold, supplied, or offered for sale [ ~~after May 1, 2010~~ on or after ] August 1, 2010, if it complies with all of the provisions of Article 2 (9VAC5-45-160 et seq.) of this part.

3. Except as provided in subdivisions 1 and 2 of this subsection, displaying the date of manufacture, or a code indicating the date of manufacture, on the product container or package does not exempt the owner or product from the provisions of this article.

Article 2
Emission Standards for Portable Fuel Containers and Spouts Manufactured [ ~~On or After May 1, 2010~~ on or after ] August 1, 2010

A. Except as provided in 9VAC5-45-170, the provisions of this article apply to any portable fuel container or spout manufactured on or after [ ~~May 1, 2010~~ ] August 1, 2010. The provisions of Article 1 (9VAC5-45-60 et seq.) of this part apply to portable fuel containers and spouts manufactured before [ ~~May 1, 2010~~ ] August 1, 2010.

B. Except as provided in 9VAC5-45-170, the provisions of this article apply to any owner or other person who sells, supplies, offers for sale, advertises for sale, or manufactures for sale portable fuel containers or spouts.

C. The provisions of this article apply only to owners and other persons in the Northern Virginia ~~and~~, Fredericksburg, and Richmond Volatile Organic Compound Emissions Control Areas designated in 9VAC5-20-206.

B. The provisions of this article do not apply to a manufacturer or distributor who sells, supplies, or offers for sale a portable fuel container or spout that does not comply with the emission standards specified in 9VAC5-45-190, as long as the manufacturer or distributor can demonstrate that: (i) the portable fuel container or spout is intended for shipment and use outside of the applicable volatile organic compound emissions control areas designated in 9VAC5-45-160 C; and (ii) the manufacturer or distributor has taken reasonable prudent precautions to assure that the portable fuel container or spout is not distributed within the applicable volatile organic compound emissions control areas designated in 9VAC5-45-160 C. This subsection does not apply to portable fuel containers or spouts that are sold, supplied, or offered for sale to retail outlets.

C. The provisions of this article do not apply to safety cans meeting the requirements of ~~subpart F of~~ 29 CFR Part 1926 Subpart F.

D. The provisions of this article do not apply to portable fuel containers with a nominal capacity less than or equal to one quart.

E. The provisions of this article do not apply to rapid refueling devices with nominal capacities greater than or equal to four gallons provided (i) such devices are designed for use in officially sanctioned off-highway motor sports such as car racing or motorcycle competitions, and (ii) such devices either create a leak-proof seal against a stock target fuel tank, or are designed to operate in conjunction with a receiver permanently installed on the target fuel tank.

G. The provisions of this article do not apply to closed-system portable fuel containers that are used exclusively for fueling remote control model airplanes.

A. The following provisions apply to portable fuel containers and spouts manufactured on or after [ ~~May 1, 2010~~ ] August 1, 2010:

1. No owner or other person shall sell, supply, offer for sale, or advertise for sale any portable fuel container or spout manufactured on or after [ ~~May 1, 2010~~ ] August 1, 2010, unless that portable container or spout is certified by the board to be a spill-proof system or spill-proof spout that is in compliance with the standards in subsection B of this section in accordance with the certification procedures specified in 9VAC5-45-200.

2. No owner or other person shall manufacture for sale any portable fuel container or spout on or after [ ~~May 1, 2010~~ ] August 1, 2010, unless that portable container or spout is certified by the board to be a spill-proof system or spill-proof spout that is in compliance with the standards in subsection B of this section in accordance with the certification procedures specified in 9VAC5-45-200.

B. The following standards apply to each portable fuel container or spout manufactured on or after [ ~~May 1, 2010~~ ] August 1, 2010, that is subject to the provisions of this article:

b. Each portable fuel container shall have identification markings on the container and on the spill-proof spout.

(1) Red containers shall be permanently identified with the embossed language or permanent durable label "GASOLINE" in minimum 34-point Arial font or a font of equivalent proportions.

(2) Yellow containers shall be permanently identified with the embossed language or permanent durable label "DIESEL" in minimum 34-point Arial font or a font of equivalent proportions.

(3) Blue containers shall be permanently identified with the embossed language or permanent durable label "KEROSENE" in minimum 34-point Arial font or a font of equivalent proportions.

a. Portable fuel containers that are equipped with an intended spill-proof spout shall emit no more than 0.3 grams per gallon per day.

b. Compliance with emission standards in this subdivision shall be determined using the test procedure specified in 9VAC5-45-250 B 2.

c. Portable fuel containers that share similar designs, that are constructed of identical materials, and that are manufactured using identical processes, but vary only in size or color may be considered for certification as a product family.

3. Portable fuel containers and spouts shall comply with the specifications for durability in subsection 7.4 of the test procedure specified in 9VAC5-45-250 B 2.

4. There shall be no fluid leakage from any point in the spill-proof system or spill-proof spout as specified in the test procedures specified in 9VAC5-45-250 B 1 and 2.

5. The spill-proof system or spill-proof spout shall automatically close when the spill-proof spout is removed from the target tank, seal, and remain completely closed when not dispensing fuel, as specified in the test procedure specified in 9VAC5-45-250 B 1. Also, no liquid, beyond wetted surfaces, shall be retained in the spill-proof spout after fueling that may evaporate into the atmosphere.

6. An applicant seeking certification of a portable fuel container or spout from the board pursuant to this article shall also:

a. Warrant that its spill-proof system or spill-proof spout is free from defects in materials and workmanship that cause such systems or spill-proof spouts to fail to conform with each of the certification and compliance standards specified in CARB "Certification Procedure 501 for Portable Fuel Containers and Spill-Proof Spouts, CP-501," for a period of one year from the date of sale; and

b. Supply a copy of the warranty language specified in subdivision a of this subdivision that is supplied to the buyer in the packaging for each spill-proof system or spill-proof spout at the time of sale identifying the following minimum requirements:

(2) An unconditional statement that the spill-proof system or spill-proof spout is certified to the requirements in subdivision a of this subdivision (which may be referred to as being certified to California requirements); and

(3) A listing of the specific certification requirements or limitations to which it was certified.

7. An applicant shall supply a copy of the operating instructions intended for each spill-proof system or spill-proof spout, and fueling application, as supplied to the buyer in the packaging for each spill-proof system or spill-proof spout at the time of sale. These instructions shall include, at a minimum, the following specifications:

a. A listing of any specific equipment types, such as passenger cars and trucks, lawn and garden equipment, off-road motorcycles and snowmobiles, industrial equipment, and marine vessels that the spill-proof system or spill-proof spout, is not intended to refuel; and

b. Other instructions, such as the recommended fueling angle(s) or special instructions such as venting prior to use.

8. Spill-proof systems, spill-proof spouts and all components incorporated therein, such as gaskets, seals, or O-rings must demonstrate compliance with the requirements specified in 9VAC5-45-250 B 3 and 4. Applicants may request limited certification for use with only specified fuel blends. Such fuel-specific certifications shall clearly specify the limits and restrictions of the certification.

9. A portable fuel container may incorporate a secondary opening or vent hole (i.e., an opening other than the opening needed for the spout) provided the secondary opening or vent hole is not easily tampered by a consumer, and it does not emit hydrocarbon vapors in excess of the amounts specified in this section during fueling, storage, transportation, or handling events.

C. The test procedures for determining compliance with the standards in this section are set forth in 9VAC5-45-250. The manufacturer of portable fuel containers or spouts shall perform the tests for determining compliance as set forth in 9VAC5-45-250 to show that its product meets the standards of this section prior to allowing the product to be offered for sale. The manufacturer shall maintain records of these compliance tests for as long as the product is available for sale and shall make those test results available within 60 days of request.

A. Provisions follow concerning the requirements and process for board certification of a portable fuel container or spout manufactured on or after [ ~~May 1, 2010~~ ] August 1, 2010, as a spill-proof system or spill-proof spout.

B. To be considered by the board for certification, an application for certification shall be submitted in writing to the board by the manufacturer of the portable fuel container or spout.

1. Except as provided in subdivision D 2 of this section, the application shall contain the following information:

a. An identification of the names, addresses, and phone numbers of the company, owner or other persons that are submitting the application, and the names and phone numbers of contact persons that are knowledgeable concerning the application.

b. Model numbers and sizes of spill-proof systems or spill-proof spouts for which certification is requested.

c. Test data that demonstrates that the spill-proof systems or spill-proof spouts comply with each of the certification requirements identified in 9VAC5-45-190 B.

d. Engineering drawings of the spill-proof system or spill-proof spout detailing dimensions specific to each component. If an application is submitted for a spill-proof system (i.e., container and spout), separate dimensioned drawings for the portable fuel container and for the spill-proof spout are required. If more than one type or size of portable fuel container or more than one type of spill-proof spout is included in the application, separate dimensioned drawings are required for each component.

e. Test data from each of the test procedures specified in 9VAC5-45-250 B 1 and 2 demonstrating that the spill-proof system, spill-proof spout, or component meets the applicable criteria.

f. Any other test data that supports the requirements in subdivision e of this subsection and that would assist in the determination of certification.

g. The language, symbols, or patterns that will actually be permanently embossed on the spill-proof system or spill-proof spout. This shall include examples of date code wheels as well as all other permanent markings and their locations on the container and/or spill-proof spout. Once the board certifies a spill-proof system or spill-proof spout, these permanent markings cannot be altered or modified in any way without first obtaining the board's approval.

h. The language or labels that may be affixed to the spill-proof system or spill-proof spout at the time of sale.

i. The manufacturer's recommended instructions, instruction decals, or any other type of placard attached to the spill-proof system or spill-proof spout at the time of sale. Include examples of actual decals or placards if available. Proposed placards or decals are sufficient if actual samples are not available. Once the board certifies a spill-proof system or spill-proof spout, these decals or placards cannot be altered or modified in any way without first obtaining the board's approval.

k. A description of the materials used in the construction of the spill-proof system or spill-proof spout. Material compositions of gaskets, O-rings, and seals must be described.

l. If the applicant is not the manufacturer of all system components incorporated in a spill-proof system or spill-proof spout, the applicant must include evidence that the component manufacturers have been notified of the applicant's intended use of the manufacturers' components in the spill-proof system or spill-proof spout for which the application is being made.

(1) If the applicant is requesting inclusion of one or more components not manufactured by it on the applicable spill-proof system or spill-proof spout, the applicant shall notify the component manufacturers and obtain the information required of the application as specified in this subsection.

(2) If the component design and material specifications requested for inclusion in the certification have not been previously incorporated in a spill-proof system or spill-proof spout that has been issued a CARB certification executive order or has been certified by the board pursuant to these procedures, then each of the components shall be subject to each of the application and test requirements specified in this article.

m. A sample of the spill-proof system or spill-proof spout is not required as part of the initial application for certification. The board may later require that a sample be provided if it is deemed necessary to make the proper certification determination.

n. The document certification statement required by 9VAC5-20-230, signed by a responsible official as defined in that section.

o. The information required by subdivision B 1 a of this section is public information that may not be claimed as confidential. Other information submitted to the board to meet the requirements of this article shall be available to the public except where the owner makes a showing satisfactory to the board under 9VAC5-170-60 B that the information meets the criteria in 9VAC5-170-60 C, in which case the information shall be handled in accordance with the procedures specified in §§ 10.1-1314 and 10.1-1314.1 of the Air Pollution Control Law of Virginia.

2. In accordance with the time periods specified in subsection C of this section, the board will certify a portable fuel container or spout. The board will specify such terms and conditions as are necessary to ensure that the emissions from the portable fuel containers or spouts do not exceed the VOC standards specified in 9VAC5-45-190. The certification shall also include operational terms, conditions, and data to be reported to the board to ensure that all requirements of this article are met.

C. Provisions follow concerning the portable fuel container or spout certification time frames.

1. The board will take appropriate action on an application within the following time periods:

a. Within 30 working days of receipt of an application, the board will inform the applicant in writing that either:

(2) The application is deficient, and identify the specific information required to make the application complete.

b. Within 30 working days of receipt of additional information provided in response to a determination that an application is deficient, the board will inform the applicant in writing that either:

(1) The additional information is sufficient to make the application complete, and the application is accepted for filing, or

(2) The application is deficient, and identify the specific information required to make the application complete.

c. If the board finds that an application meets the requirements of subsection B of this section, then it shall certify that the requirements have been met in accordance with the requirements of this article. The board will normally act to approve or disapprove a complete application within 90 working days after the application is deemed complete. The board may extend this time period if additional information is needed.

2. [ ~~The board may extend the time period in subdivision 1 c of this subsection if additional information is needed.~~ ] Before the end of each time period specified in this section, the board and the applicant may mutually agree to a longer time period for the board to take the appropriate action.

D. In accordance with the following procedures, the board will take into consideration whether the portable fuel container or spout has been certified by CARB.

1. In lieu of granting certification based upon review of an application as required under subsection B of this section, certification may be granted by the board as follows:

a. Certification may be granted solely on the basis of the effective CARB certification executive order, or

b. Certification may be granted on the basis of the effective CARB certification executive order, modified as necessary by the board to meet the requirements of this article.

2. An abbreviated application may be submitted by a manufacturer requesting certification by the board under subdivision 1 of this subsection. The abbreviated application shall include, as a minimum:

a. A request by the manufacturer that certification be granted by the board based upon an effective CARB certification executive order.

b. A copy of the effective CARB certification executive order, including all conditions established by CARB applicable to the CARB certification executive order.

c. A certification that the manufacturer will (i) comply with the applicable CARB certification executive order within the volatile organic compound emissions control areas specified in 9VAC5-45-160 C and (ii) comply with any additional terms and conditions that the board may specify in granting certification under this subsection.

d. Manufacturer and product information as specified in subdivisions B 1 a and b of this section.

e. The document certification statement required by 9VAC5-20-230 certifying the information in the application and signed by a responsible official.

[ 4. ] 3. The board's certification shall contain such terms and conditions as necessary to adapt terms and conditions in the CARB certification executive order to satisfy the provisions of this article.

[ 5. ] 4. Any board certification granted under this subsection is contingent upon the effective CARB certification executive order provided with the application. Board certification granted on the basis of this subsection automatically expires on the date that the CARB certification executive order upon which it was based is no longer effective.

A. Affected persons shall comply with the provisions of this article as expeditiously as possible but in no case later than ~~August 1, 2010~~ [ ~~May 1, 2010.~~:

1. August 1, 2010, in the Northern Virginia and Fredericksburg VOC Emissions Control Areas; or

B. Any owner or other person who cannot comply with the provisions of this article by the date specified in subsection A of this section, due to extraordinary reasons beyond that person's reasonable control, may apply in writing to the board for a waiver. The waiver application shall set forth:

1. The specific grounds upon which the waiver is sought, including the facts that support the extraordinary reasons that compliance is beyond the applicant's reasonable control;

2. The proposed date by which compliance with the provisions of this article will be achieved; and

3. A compliance report detailing the methods by which compliance will be achieved.

1. That, due to reasons beyond the reasonable control of the applicant, required compliance with this article would result in extraordinary economic hardship;

2. That the public interest in mitigating the extraordinary hardship to the applicant by issuing the waiver outweighs the public interest in avoiding any increased emissions of air contaminants that would result from issuing the waiver; and

3. That the compliance report proposed by the applicant can reasonably be implemented and shall achieve compliance as expeditiously as possible.

D. Any approval of a waiver shall specify a final compliance date by which compliance with the requirements of this article shall be achieved. Any approval of a waiver shall contain a condition that specifies the increments of progress necessary to assure timely compliance and such other conditions that the board finds necessary to carry out the purposes of this article.

E. A waiver shall cease to be effective upon the failure of the party to whom the waiver was granted to comply with any term or condition of the waiver.

F. Upon the application of any person, the board may review, and for good cause, modify or revoke a waiver from requirements of this article.

Article 3
Emission Standards for Consumer Products Manufactured before [ ~~May 1, 2010~~ ] August 1, 2010

A. Except as provided in 9VAC5-45-290, the provisions of this article apply to any consumer product manufactured before [ ~~May 1, 2010~~ ] August 1, 2010, that contains volatile organic compounds (VOCs). The provisions of Article 4 (9VAC5-45-400 et seq.) of this part apply to consumer products manufactured on or after [ ~~May 1, 2010~~ ] August 1, 2010.

B. Except as provided in 9VAC5-45-290, the provisions of this article apply to any owner or other person who sells, supplies, offers for sale or manufactures for sale any consumer product.

C. The provisions of this article apply to owners and other persons in the Northern Virginia and Fredericksburg Volatile Organic Compound Emissions Control Areas designated in 9VAC5-20-206.

D. For purposes of this article, the terms "supply" or "supplied" do not include internal transactions within a business or governmental entity. These terms only apply to transactions between manufacturers/commercial distributors that sell, or otherwise provide, products to businesses/governmental entities/individuals.

A. Except as provided in 9VAC5-45-290, 9VAC5-45-320, and 9VAC5-45-330, no owner or other person shall (i) sell, supply, or offer for sale a consumer product manufactured on or after the applicable compliance date specified in 9VAC5-45-360 or (ii) manufacture for sale a consumer product on or after the applicable compliance date specified in 9VAC5-45-360, that contains volatile organic compounds in excess of the limits specified in Table 45-3A.

B. No owner or other person shall sell, supply, offer for sale, or manufacture for sale an antiperspirant or a deodorant that contains a compound that has been defined as a toxic pollutant in 9VAC5-60-210 C.

1. For consumer products for which the label, packaging, or accompanying literature specifically states that the product should be diluted with water or non-VOC solvent prior to use, the limits specified in Table 45-3A shall apply to the product only after the minimum recommended dilution has taken place. For purposes of this subsection, "minimum recommended dilution" shall not include recommendations for incidental use of a concentrated product to deal with limited special applications such as hard-to-remove soils or stains.

2. For consumer products for which the label, packaging, or accompanying literature states that the product should be diluted with a VOC solvent prior to use, the limits specified in Table 45-3A shall apply to the product only after the maximum recommended dilution has taken place.

D. The following provisions apply to sell through of consumer products manufactured before [ ~~May 1, 2010~~ ] August 1, 2010:

1. Notwithstanding the provisions of [ ~~subsections~~ subsection ] A [ ~~and~~, ] G, H or I of this section, a consumer product manufactured before the applicable compliance date specified in 9VAC5-45-360, may be sold, supplied, or offered for sale after the applicable compliance date if the date of manufacture or a date code representing the date of manufacture is clearly displayed on the product container or package.

2. Notwithstanding the provisions of [ ~~subsections~~ subsection ] A [ ~~and~~, ] G, H, or I of this section, a consumer product manufactured after the applicable compliance date specified in 9VAC5-45-360 and before [ ~~May 1, 2010~~ ] August 1, 2010, may be sold, supplied, or offered for sale [ ~~after May 1, 2010~~ ] on or after August 1, 2010, if it complies with all of the provisions of Article 4 (9VAC5-45-400 et seq.) of this part.

E. For those consumer products that are registered under FIFRA, the effective date of the VOC standards shall be one year after the applicable compliance date specified in 9VAC5-45-360.

F. The following requirements shall apply to all charcoal lighter material products:

1. Effective as of the applicable compliance date specified in 9VAC5-45-360, no owner or other person shall (i) sell, supply, or offer for sale a charcoal lighter material product manufactured on or after the applicable compliance date or (ii) manufacture for sale a charcoal lighter material product unless at the time of the transaction:

a. The manufacturer can demonstrate to the board's satisfaction that it has been issued a currently effective certification by CARB under the Consumer Products provisions under Subchapter 8.5, Article 2, § 94509(h), of Title 17 of the California Code of Regulations (see 9VAC5-20-21). This certification remains in effect for as long as the CARB certification remains in effect. A manufacturer claiming such a certification on this basis must submit to the board a copy of the certification decision (i.e., the executive order), including all conditions established by CARB applicable to the certification.

b. The manufacturer or distributor of the charcoal lighter material has been issued a currently effective certification pursuant to subdivision 2 of this subsection.

c. The charcoal lighter material meets the formulation criteria and other conditions specified in the applicable ACP agreement issued pursuant to subdivision 2 of this subsection.

d. The product usage directions for the charcoal lighter material are the same as those provided to the board pursuant to subdivision 2 c of this subsection.

a. No charcoal lighter material formulation shall be certified under this subdivision unless the applicant for certification demonstrates to the board's satisfaction that the VOC emissions from the ignition of charcoal with the charcoal lighter material are less than or equal to 0.020 pound of VOC per start, using the procedures specified in the South Coast Air Quality Management District Rule 1174 Ignition Method Compliance Certification Protocol (see 9VAC5-20-21). The provisions relating to LVP-VOC in 9VAC5-45-290 F and 9VAC5-45-300 C shall not apply to a charcoal lighter material subject to the requirements of 9VAC5-45-310 A and this subsection.

b. The board may approve alternative test procedures that are shown to provide equivalent results to those obtained using the South Coast Air Quality Management District Rule 1174 Ignition Method Compliance Certification Protocol (see 9VAC5-20-21).

c. A manufacturer or distributor of charcoal lighter material may apply to the board for certification of a charcoal lighter material formulation in accordance with this subdivision. The application shall be in writing and shall include, at a minimum, the following:

(1) The results of testing conducted pursuant to the procedures specified in South Coast Air Quality Management District Rule 1174 Testing Protocol (see 9VAC5-20-21); and

(2) The exact text or graphics that will appear on the charcoal lighter material's principal display panel, label, or accompanying literature. The provided material shall clearly show the usage directions for the product. These directions shall accurately reflect the quantity of charcoal lighter material per pound of charcoal that was used in the South Coast Air Quality Management District Rule 1174 Testing Protocol (see 9VAC5-20-21) for that product, unless:

(a) The charcoal lighter material is intended to be used in fixed amounts independent of the amount of charcoal used, such as certain paraffin cubes, or

(b) The charcoal lighter material is already incorporated into the charcoal, such as certain "bag light," "instant light" or "match light" products.

(3) For a charcoal lighter material that meets the criteria specified in subdivision 2 c (2) (a) of this subsection, the usage instructions provided to the board will accurately reflect the quantity of charcoal lighter material used in the South Coast Air Quality Management District Rule 1174 Testing Protocol (see 9VAC5-20-21) for that product.

(4) Physical property data, formulation data, or other information required by the board for use in determining when a product modification has occurred and for use in determining compliance with the conditions specified on the ACP agreement issued pursuant to subdivision 2 e of this subsection.

d. Within 30 days of receipt of an application, the board will advise the applicant in writing either that it is complete or that specified additional information is required to make it complete. Within 30 days of receipt of additional information, the board will advise the applicant in writing either that the application is complete, or that specified additional information or testing is still required before it can be deemed complete.

e. If the board finds that an application meets the requirements of subdivision 2 of this subsection, then an ACP agreement shall be issued certifying the charcoal lighter material formulation and specifying such conditions as are necessary to insure that the requirements of this subsection are met. The board will act on a complete application within 90 days after the application is deemed complete.

3. For charcoal lighter material for which certification has been granted pursuant to subdivision 2 of this subsection, the applicant for certification shall notify the board in writing within 30 days of: (i) a change in the usage directions, or (ii) a change in product formulation, test results, or other information submitted pursuant to subdivision 2 of this subsection that may result in VOC emissions greater than 0.020 pound of VOC per start.

4. If the board determines that a certified charcoal lighter material formulation results in VOC emissions from the ignition of charcoal that are greater than 0.020 pound of VOC per start, as determined by the South Coast Air Quality Management District Rule 1174 Testing Protocol (see 9VAC5-20-21) and the statistical analysis procedures contained therein, the board will revoke or modify the certification as is necessary to assure that the charcoal lighter material will result in VOC emissions of less than or equal to 0.020 pound of VOC per start.

1. The standards for aerosol adhesives apply to all uses of aerosol adhesives, including consumer, industrial, and commercial uses. Except as otherwise provided in 9VAC5-45-290 and 9VAC5-45-330, no owner or other person shall sell, supply, offer for sale, use, or manufacture for sale an aerosol adhesive that, at the time of sale, use, or manufacture, contains VOCs in excess of the specified standard.

2. a. In order to qualify as a "special purpose spray adhesive," the product must meet one or more of the definitions for special purpose spray adhesive specified in 9VAC5-45-300 C, but if the product label indicates that the product is suitable for use on a substrate or application not listed in 9VAC5-45-300 C, then the product shall be classified as either a "web spray adhesive" or a "mist spray adhesive."

b. If a product meets more than one of the definitions specified in 9VAC5-45-300 C for "special purpose spray adhesive," and is not classified as a "web spray adhesive" or "mist spray adhesive" under subdivision 2 a of this subsection, then the VOC limit for the product shall be the lowest applicable VOC limit specified in 9VAC5-45-310 A.

3. Effective as of the applicable compliance dates specified in 9VAC5-45-360, no person shall (i) sell, supply, or offer for sale an aerosol adhesive manufactured on or after the applicable compliance date or (ii) manufacture for sale an aerosol adhesive that contains any of the following compounds: methylene chloride, perchloroethylene, or trichloroethylene.

4. All aerosol adhesives must comply with the labeling requirements specified in 9VAC5-45-340 D.

H. Effective as of the applicable compliance date specified in 9VAC5-45-360, no owner or other person shall sell, supply, offer for sale, or manufacture for use a floor wax stripper unless the following requirements are met:

1. The label of each nonaerosol floor wax stripper must specify a dilution ratio for light or medium build-up of polish that results in an as-used VOC concentration of 3.0% by weight or less.

2. If a nonaerosol floor wax stripper is also intended to be used for removal of heavy build-up of polish, the label of that floor wax stripper must specify a dilution ratio for heavy build-up of polish that results in an as-used VOC concentration of 12% by weight or less.

3. The terms "light build-up," "medium build-up" or "heavy build-up" are not specifically required as long as comparable terminology is used.

I. For a consumer product for which standards are specified under subsection A of this section, no owner or other person shall sell, supply, offer for sale, or manufacture for sale a consumer product that contains any of the following ozone-depleting compounds:

HCFC-141b (1,1-dichloro-1-fluoroethane), HCFC-142b (1-chloro-1,1-difluoroethane);

J. The requirements of subsection I of this section shall not apply to an existing product formulation that complies with Table 45-3A or an existing product formulation that is reformulated to meet Table 45-3A, provided the ozone-depleting compound content of the reformulated product does not increase.

K. The requirements of subsection I of this section shall not apply to ozone-depleting compounds that may be present as impurities in a consumer product in an amount equal to or less than 0.01% by weight of the product.

A. 1. Manufacturers of consumer products may seek an ACP agreement in accordance with subsections B through L of this section.

2. Only responsible ACP parties for consumer products may enter into an ACP agreement under the provisions of this section.

B. Provisions follow concerning the requirements and process for approval of an ACP.

1. To be considered by the board for approval, an application for a proposed ACP shall be submitted in writing to the board by the responsible ACP party and shall contain all of the following:

a. An identification of the contact persons, phone numbers, names, and addresses of the responsible ACP party that is submitting the ACP application and will be implementing the ACP requirements specified in the ACP agreement.

b. A statement of whether the responsible ACP party is a small business or a one-product business.

c. A listing of the exact product brand name, form, available variations (flavors, scents, colors, sizes, etc.), and applicable product category for each distinct ACP product that is proposed for inclusion in the ACP.

d. For each proposed ACP product identified in subdivision 1 c of this subsection, a demonstration to the satisfaction of the board that the enforceable sales records to be used by the responsible ACP party for tracking product sales meet the minimum criteria specified in subdivision 1 d (5) of this subsection. To provide this demonstration, the responsible ACP party shall either demonstrate to the satisfaction of the board that other records provided to the board in writing by the responsible ACP party meet the minimum criteria of subdivision 1 d (5) of this subsection for tracking product sales of each ACP product, or do all of the following:

(1) Provide the contact persons, phone numbers, names, street and mail addresses of all persons and businesses who will provide information that will be used to determine the enforceable sales;

(2) Determine the enforceable sales of each product using enforceable sales records;

(3) Demonstrate, to the satisfaction of the board, the validity of the enforceable sales based on enforceable sales records provided by the contact persons or the responsible ACP party;

(4) Calculate the percentage of the gross sales that is composed of enforceable sales; and

(5) Determine which ACP products have enforceable sales that are 75% or more of the gross sales. Only ACP products meeting this criteria shall be allowed to be sold under an ACP.

e. For each of the ACP products identified in subdivision 1 d (5) of this subsection, the inclusion of the following:

(2) The VOC content and LVP content for each product. The VOC content and LVP content shall be reported for two different periods as follows:

(a) The VOC and LVP contents of the product at the time the application for an ACP is submitted, and

(b) The VOC and LVP contents of the product that were used at any time within the four years prior to the date of submittal of the application for an ACP if either the VOC or LVP contents have varied by more than plus or minus 10% of the VOC or LVP contents reported in subdivision 1 e (2) (a) of this subsection.

f. A written commitment obligating the responsible ACP party to date-code every unit of each ACP product approved for inclusion in the ACP. The commitment shall require the responsible ACP party to display the date-code on each ACP product container or package no later than five working days after the date an ACP agreement approving an ACP is signed by the board.

g. An operational plan covering all the products identified under subdivision 1 d (5) of this subsection for each compliance period that the ACP will be in effect. The operational plan shall contain all of the following:

(1) An identification of the compliance periods and dates for the responsible ACP party to report the information required by the board in the ACP agreement approving an ACP. The length of the compliance period shall be chosen by the responsible ACP party (not to exceed 365 days). The responsible ACP party shall also choose the dates for reporting information such that all required VOC content and enforceable sales data for all ACP products shall be reported to the board at the same time and at the same frequency .

(2) An identification of specific enforceable sales records to be provided to the board for enforcing the provisions of this article and the ACP agreement approving an ACP. The enforceable sales records shall be provided to the board no later than the compliance period dates specified in subdivision 1 g (1) of this subsection.

(3) For a small business or a one-product business that will be relying to some extent on surplus trading to meet its ACP limits, a written commitment from the responsible ACP party that they will transfer the surplus reductions to the small business or one-product business upon approval of the ACP.

(4) For each ACP product, all VOC content levels that will be applicable for the ACP product during each compliance period. The plan shall also identify the specific method by which the VOC content will be determined and the statistical accuracy and precision (repeatability and reproducibility) will be calculated for each specified method.

(5) The projected enforceable sales for each ACP product at each different VOC content for every compliance period that the ACP will be in effect.

(6) A detailed demonstration showing the combination of specific ACP reformulations or surplus trading (if applicable) that is sufficient to ensure that the ACP emissions will not exceed the ACP limit for each compliance period that the ACP will be in effect, the approximate date within each compliance period that such reformulations or surplus trading are expected to occur, and the extent to which the VOC contents of the ACP products will be reduced (i.e., by ACP reformulation). This demonstration shall use the equations specified in 9VAC5-45-300 C for projecting the ACP emissions and ACP limits during each compliance period. This demonstration shall also include all VOC content levels and projected enforceable sales for all ACP products to be sold during each compliance period.

(7) A certification that all reductions in the VOC content of a product will be real, actual reductions that do not result from changing product names, mischaracterizing ACP product reformulations that have occurred in the past, or other attempts to circumvent the provisions of this article.

(8) Written explanations of the date-codes that will be displayed on each ACP product's container or packaging.

(9) A statement of the approximate dates by which the responsible ACP party plans to meet the applicable ACP VOC standards for each product in the ACP.

(10) An operational plan ("reconciliation of shortfalls plan") that commits the responsible ACP party to completely reconcile shortfalls, even, to the extent permitted by law, if the responsible ACP party files for bankruptcy protection. The plan for reconciliation of shortfalls shall contain all of the following:

(a) A clear and convincing demonstration of how shortfalls of up to 5.0%, 10%, 15%, 25%, 50%, 75% and 100% of the applicable ACP limit will be completely reconciled within 90 working days from the date the shortfall is determined;

(b) A listing of the specific records and other information that will be necessary to verify that the shortfalls were reconciled as specified in this subsection; and

(c) A commitment to provide a record or information requested by the board to verify that the shortfalls have been completely reconciled.

h. A declaration, signed by a legal representative for the responsible ACP party, that states that all information and operational plans submitted with the ACP application are true and correct.

2. a. In accordance with the time periods specified in subsection C of this section, the board will issue an ACP agreement approving an ACP that meets the requirements of this article. The board will specify such terms and conditions as are necessary to ensure that the emissions from the ACP products do not exceed the emissions that would have occurred if the ACP products subject to the ACP had met the VOC standards specified in 9VAC5-45-310 A. The ACP shall also include:

(1) Only those ACP products for which the enforceable sales are at least 75% of the gross sales as determined in subdivision 1 d (5) of this subsection;

(2) A reconciliation of shortfalls plan meeting the requirements of this article; and

(3) Operational terms, conditions, and data to be reported to the board to ensure that all requirements of this article are met.

b. The board will not approve an ACP submitted by a responsible ACP party if the board determines, upon review of the responsible ACP party's compliance history with past or current ACPs or the requirements for consumer products in this article, that the responsible ACP party has a recurring pattern of violations and has consistently refused to take the necessary steps to correct those violations.

1. The board will take appropriate action on an ACP within the following time periods:

a. Within 30 working days of receipt of an ACP application, the board will inform the applicant in writing that either:

(2) The application is deficient, and identify the specific information required to make the application complete.

b. Within 30 working days of receipt of additional information provided in response to a determination that an ACP application is deficient, the board will inform the applicant in writing that either:

(1) The additional information is sufficient to make the application complete, and the application is accepted for filing, or

(2) The application is deficient, and identify the specific information required to make the application complete.

c. If the board finds that an application meets the requirements of subsection B of this section, then it shall issue an ACP agreement in accordance with the requirements of this article. The board will normally act to approve or disapprove a complete application within 90 working days after the application is deemed complete. The board may extend this time period if additional information is needed.

2. [ ~~The board may extend the time period in subdivision 1 c of this subsection if additional information is needed.~~ ] Before the end of each time period specified in this section, the board and the responsible ACP party may mutually agree to a longer time period for the board to take the appropriate action.

D. Provisions follow concerning recordkeeping and availability of requested information.

1. All information specified in the ACP agreement approving an ACP shall be maintained by the responsible ACP party for a minimum of three years after such records are generated. Such records shall be clearly legible and maintained in good condition during this period.

2. The records specified in subdivision 1 of this subsection shall be made available to the board or its authorized representative:

a. Immediately upon request, during an on-site visit to a responsible ACP party,

b. Within five working days after receipt of a written request from the board, or

c. Within a time period mutually agreed upon by both the board and the responsible ACP party.

1. Failure to meet a requirement of this article or a condition of an applicable ACP agreement shall constitute a single, separate violation of this article for each day until such requirement or condition is satisfied, except as otherwise provided in subdivisions 2 through 8 of this subsection.

2. False reporting of information in an ACP application or in any supporting documentation or amendments thereto shall constitute a single, separate violation of the requirements of this article for each day that the approved ACP is in effect.

3. An exceedance during the applicable compliance period of the VOC content specified for an ACP product in the ACP agreement approving an ACP shall constitute a single, separate violation of the requirements of this article for each ACP product that exceeds the specified VOC content that is sold, supplied, offered for sale, or manufactured for use.

4. Any of the following actions shall each constitute a single, separate violation of the requirements of this article for each day after the applicable deadline until the requirement is satisfied:

a. Failure to report data or failure to report data accurately in writing to the board regarding the VOC content, LVP content, enforceable sales, or other information required by the deadline specified in the applicable ACP agreement;

b. False reporting of information submitted to the board for determining compliance with the ACP requirements;

c. Failure to completely implement the reconciliation of shortfalls plan that is set forth in the ACP agreement within 30 working days from the date of written notification of a shortfall by the board; or

d. Failure to completely reconcile the shortfall as specified in the ACP agreement within 90 working days from the date of written notification of a shortfall by the board.

5. False reporting or failure to report any of the information specified in subdivision F 2 i of this section or the sale or transfer of invalid surplus reductions shall constitute a single, separate violation of the requirements of this article for each day during the time period for which the surplus reductions are claimed to be valid.

6. Except as provided in subdivision 7 of this subsection, an exceedance of the ACP limit for a compliance period that the ACP is in effect shall constitute a single, separate violation of the requirements of this article for each day of the applicable compliance period. The board will determine whether an exceedance of the ACP limit has occurred as follows:

a. If the responsible ACP party has provided all required information for the applicable compliance period specified in the ACP agreement approving an ACP, then the board will determine whether an exceedance has occurred using the enforceable sales records and VOC content for each ACP product as reported by the responsible ACP party for the applicable compliance period.

b. If the responsible ACP party has failed to provide all the required information specified in the ACP agreement for an applicable compliance period, the board will determine whether an exceedance of the ACP limit has occurred as follows.

(1) For the missing data days, the board will calculate the total maximum historical emissions as specified in 9VAC5-45-300 C.

(2) For the remaining portion of the compliance period that are not missing data days, the board will calculate the emissions for each ACP product using the enforceable sales records and VOC content that were reported for that portion of the applicable compliance period.

(3) The ACP emissions for the entire compliance period shall be the sum of the total maximum historical emissions, determined pursuant to subdivision 6 b (1) of this subsection, and the emissions determined pursuant to subdivision 6 b (2) of this subsection.

(4) The board will calculate the ACP limit for the entire compliance period using the ACP standards applicable to each ACP product and the enforceable sales records specified in subdivision 6 b (2) of this subsection. The enforceable sales for each ACP product during missing data days, as specified in subdivision 6 b (1) of this subsection, shall be zero.

(5) An exceedance of the ACP limit has occurred when the ACP emissions, determined pursuant to subdivision 6 b (3) of this subsection, exceeds the ACP limit, determined pursuant to subdivision 6 b (4) of this subsection.

7. If a violation specified in subdivision 6 of this subsection occurs, the responsible ACP party may, pursuant to this subdivision, establish the number of violations as calculated according to the following equation:

The responsible ACP party may determine the number of ACP limit violations pursuant to this subdivision only if it has provided all required information for the applicable compliance period, as specified in the ACP agreement approving the ACP. By choosing this option, the responsible ACP party waives all legal objections to the calculation of the ACP limit violations pursuant to this subdivision.

8. A cause of action against a responsible ACP party under this section shall be deemed to accrue on the date when the records establishing a violation are received by the board.

9. The responsible ACP party is fully liable for compliance with the requirements of this article, even if the responsible ACP party contracts with or otherwise relies on another person to carry out some or all of the requirements of this article.

1. The board will issue surplus reduction certificates that establish and quantify, to the nearest pound of VOC reduced, the surplus reductions achieved by a responsible ACP party operating under an ACP. The surplus reductions can be bought from, sold to, or transferred to a responsible ACP party operating under an ACP, as provided in subdivision 2 of this subsection. All surplus reductions shall be calculated by the board at the end of each compliance period within the time specified in the approved ACP. Surplus reduction certificates shall not constitute instruments, securities, or another form of property.

2. The issuance, use, and trading of all surplus reductions shall be subject to the following provisions:

a. For the purposes of this article, VOC reductions from sources of VOCs other than consumer products subject to the VOC standards specified in 9VAC5-45-310 A may not be used to generate surplus reductions.

b. Surplus reductions are valid only when generated by a responsible ACP party and only while that responsible ACP party is operating under an approved ACP.

c. Surplus reductions are valid only after the board has issued an ACP agreement pursuant to subdivision 1 of this subsection.

d. Surplus reductions issued by the board may be used by the responsible ACP party who generated the surplus until the reductions expire, are traded, or until the ACP is canceled pursuant to subdivision J 2 of this section.

e. Surplus reductions cannot be applied retroactively to a compliance period prior to the compliance period in which the reductions were generated.

f. Except as provided in subdivision 2 g (2) of this subsection, only small or one-product businesses selling products under an approved ACP may purchase surplus reductions. An increase in the size of a small business or one-product business shall have no effect on surplus reductions purchased by that business prior to the date of the increase.

(1) To adjust the ACP emissions of either the responsible ACP party who generated the reductions or the responsible ACP party to which the reductions were traded, provided the surplus reductions are not to be used by a responsible ACP party to further lower its ACP emissions when its ACP emissions are equal to or less than the ACP limit during the applicable compliance period; or

(2) To be traded for the purpose of reconciling another responsible ACP party's shortfalls, provided such reconciliation is part of the reconciliation of shortfalls plan approved by the board pursuant to subdivision B 1 g (10) of this section.

h. A valid surplus reduction shall be in effect starting five days after the date of issuance by the board for a continuous period equal to the number of days in the compliance period during which the surplus reduction was generated. The surplus reduction shall then expire at the end of its effective period.

i. At least five working days prior to the effective date of transfer of surplus reductions, both the responsible ACP party that is selling surplus reductions and the responsible ACP party that is buying the surplus reductions shall, either together or separately, notify the board in writing of the transfer. The notification shall include all of the following:

(3) The amount (in pounds of VOCs) of surplus reductions that is being transferred.

(5) The contact persons, names of the companies, street and mail addresses, and phone numbers of the responsible ACP parties involved in the trading of the surplus reductions.

(6) A copy of the board-issued surplus reductions certificate, signed by both the seller and buyer of the certificate, showing transfer of all or a specified portion of the surplus reductions. The copy shall show the amount of any remaining nontraded surplus reductions, if applicable, and shall show their expiration date. The copy shall indicate that both the buyer and seller of the surplus reductions fully understand the conditions and limitations placed upon the transfer of the surplus reductions and accept full responsibility for the appropriate use of such surplus reductions as provided in this section.

3. Provisions follow concerning limited-use surplus reduction credits for early reformulations of ACP products.

a. For the purposes of this subdivision, "early reformulation" means an ACP product that is reformulated to result in a reduction in the product's VOC content, and that is sold, supplied, or offered for sale for the first time during the one-year (365 day) period immediately prior to the date on which the application for a proposed ACP is submitted to the board. Early reformulation does not include reformulated ACP products that are sold, supplied, or offered for sale more than one year prior to the date on which the ACP application is submitted to the board.

b. If requested in the application for a proposed ACP, the board will, upon approval of the ACP, issue surplus reduction credits for early reformulation of ACP products, provided that all of the following documentation has been provided by the responsible ACP party to the satisfaction of the board:

(1) Accurate documentation showing that the early reformulation reduced the VOC content of the ACP product to a level that is below the pre-ACP VOC content of the product or below the applicable VOC standard specified in 9VAC 5-45-310 A, whichever is the lesser of the two;

(2) Accurate documentation demonstrating that the early reformulated ACP product was sold in retail outlets within the time period specified in subdivision 3 a of this subsection;

(3) Accurate sales records for the early reformulated ACP product that meet the definition of enforceable sales records and that demonstrate that the enforceable sales for the ACP product are at least 75% of the gross sales for the product, as specified in subdivision B 1 d of this section; and

(4) Accurate documentation for the early reformulated ACP product that meets the requirements specified in subdivisions B 1 c and d and B 1 g (7) and (8) of this section and that identifies the specific test methods for verifying the claimed early reformulation and the statistical accuracy and precision of the test methods as specified in subdivision B 1 g (4) of this section.

c. Surplus reduction credits issued pursuant to this subsection shall be calculated separately for each early reformulated ACP product by the board according to the following equation:

Enforceable sales = the enforceable sales for the early reformulated ACP product, expressed to the nearest pound of ACP product.

VOC content_initial = the pre-ACP VOC content of the ACP product, or the applicable VOC standard specified in 9VAC5-45-310 A, whichever is the lesser of the two, expressed to the nearest 0.1 pounds of VOC per 100 pounds of ACP product.

VOC content_final = the VOC content of the early reformulated ACP product after the early reformulation is achieved, expressed to the nearest 0.1 pounds of VOC per 100 pounds of ACP product.

d. The use of limited use surplus reduction credits issued pursuant to this subdivision shall be subject to all of the following provisions:

(1) Limited use surplus reduction credits shall be used solely to reconcile the responsible ACP party's shortfalls, if any, generated during the first compliance period occurring immediately after the issuance of the ACP agreement approving an ACP, and may not be used for another purpose;

(2) Limited use surplus reduction credits may not be transferred to, or used by, another responsible ACP party; and

(3) Except as provided in this subdivision, limited use surplus reduction credits shall be subject to all requirements applicable to surplus reductions and surplus trading as specified in subdivisions 1 and 2 of this subsection.

1. At the end of each compliance period, the responsible ACP party shall make an initial calculation of shortfalls occurring in that compliance period as specified in the ACP agreement approving the ACP. Upon receipt of this information, the board will determine the amount of a shortfall that has occurred during the compliance period and shall notify the responsible ACP party of this determination.

2. The responsible ACP party shall implement the reconciliation of shortfalls plan as specified in the ACP agreement approving the ACP within 30 working days from the date of written notification of a shortfall by the board.

3. All shortfalls shall be completely reconciled within 90 working days from the date of written notification of a shortfall by the board by implementing the reconciliation of shortfalls plan specified in the ACP agreement approving the ACP.

4. All requirements specified in the ACP agreement approving an ACP, including all applicable ACP limits, shall remain in effect while shortfalls are in the process of being reconciled.

H. Provisions follow concerning the notification of modifications to an ACP by the responsible ACP party.

1. Board pre-approval is not required for modifications that are a change to an ACP product's: (i) product name, (ii) product formulation, (iii) product form, (iv) product function, (v) applicable product category, (vi) VOC content, (vii) LVP content, (viii) date-codes, or (ix) recommended product usage directions. The responsible ACP party shall notify the board of such changes, in writing, no later than 15 working days from the date such a change occurs. For each modification, the notification shall fully explain the following:

b. The extent to which the ACP product formulation, VOC content, LVP content, or recommended usage directions will be changed;

c. The extent to which the ACP emissions and ACP limit specified in the ACP agreement will be changed for the applicable compliance period; and

2. The responsible ACP party may propose modifications to the enforceable sales records or the reconciliation of shortfalls plan specified in the ACP agreement approving the ACP, however, such modifications require board pre-approval. Any such proposed modifications shall be fully described in writing and forwarded to the board. The responsible ACP party shall clearly demonstrate that the proposed modifications will meet the requirements of this article. The board will act on the proposed modifications using the procedure set forth in subsection C of this section. The responsible ACP party shall meet all applicable requirements of the existing ACP until such time as a proposed modification is approved in writing by the board.

3. Except as otherwise provided in subdivisions 1 and 2 of this subsection, the responsible ACP party shall notify the board, in writing, of information known by the responsible ACP party that may alter the information submitted pursuant to the requirements of subsection B of this section. The responsible ACP party shall provide such notification to the board no later than 15 working days from the date such information is known to the responsible ACP party.

1. If the board determines that: (i) the enforceable sales for an ACP product are no longer at least 75% of the gross sales for that product, (ii) the information submitted pursuant to the approval process set forth in subsection C of this section is no longer valid, or (iii) the ACP emissions are exceeding the ACP limit specified in the ACP agreement approving an ACP, then the board will modify the ACP as necessary to ensure that the ACP meets all requirements of this article and that the ACP emissions will not exceed the ACP limit.

2. If any applicable VOC standards specified in 9VAC5-45-310 A are modified by the board in a future rulemaking, the board will modify the ACP limit specified in the ACP agreement approving an ACP to reflect the modified ACP VOC standards as of their effective dates.

b. The ACP is modified by the responsible ACP party and approved by the board as provided in subsection H of this section;

c. The ACP is modified by the board as provided in subsection I of this section;

d. The ACP includes a product for which the VOC standard specified in 9VAC5-45-310 A is modified by the board in a future rulemaking, and the responsible ACP party informs the board in writing that the ACP will terminate on the effective date of the modified standard; or

a. The responsible ACP party demonstrates to the satisfaction of the board that the continuation of the ACP will result in an extraordinary economic hardship.

b. The responsible ACP party violates the requirements of the approved ACP, and the violation results in a shortfall that is 20% or more of the applicable ACP limit (i.e., the ACP emissions exceed the ACP limit by 20% or more).

c. The responsible ACP party fails to meet the requirements of subsection G of this section within the time periods specified in that subsection.

d. The responsible ACP party has demonstrated a recurring pattern of violations and has consistently failed to take the necessary steps to correct those violations.

3. Cancellations of ACPs are considered case decisions and will be processed using the procedures prescribed in 9VAC5-170-40 A 2 and applicable provisions of Article 3 (§ 2.2-4018 et seq.) of the Administrative Process Act.

4. The responsible ACP party for an ACP that is canceled pursuant to this section and who does not have a valid ACP to immediately replace the canceled ACP shall meet all of the following requirements:

a. All remaining shortfalls in effect at the time of ACP cancellation shall be reconciled in accordance with the requirements of subsection G of this section, and

b. All ACP products subject to the ACP shall be in compliance with the applicable VOC standards in 9VAC5-45-310 A immediately upon the effective date of ACP cancellation.

5. Violations incurred pursuant to subsection E of this section shall not be cancelled or affected by the subsequent cancellation or modification of an ACP pursuant to subsection H, I, or J of this section.

K. The information required by subdivisions B 1 a and b and F 2 i of this section is public information that may not be claimed as confidential. Other information submitted to the board to meet the requirements of this section shall be available to the public except where the owner makes a showing satisfactory to the board under 9VAC5-170-60 B that the information meets the criteria in 9VAC5-170-60 C, in which case the information shall be handled in accordance with the procedures specified in §§ 10.1-1314 and 10.1-1314.1 of the Air Pollution Control Law of Virginia.

L. A responsible ACP party may transfer an ACP to another responsible ACP party, provided that all of the following conditions are met:

1. The board will be notified, in writing, by both responsible ACP parties participating in the transfer of the ACP and its associated ACP agreement. The written notifications shall be postmarked at least five working days prior to the effective date of the transfer and shall be signed and submitted separately by both responsible parties. The written notifications shall clearly identify the contact persons, business names, mail and street addresses, and phone numbers of the responsible parties involved in the transfer.

2. The responsible ACP party to which the ACP is being transferred shall provide a written declaration stating that the transferee shall fully comply with all requirements of the ACP agreement approving the ACP and this article.

M. In approving agreements under subsections B through L of this section, the board will take into consideration whether the applicant has been granted an ACP by CARB. A manufacturer of consumer products that has been granted an ACP agreement by the CARB under the provisions in Subchapter 8.5, Article 4, Sections 94540-94555, of Title 17 of the California Code of Regulations (see 9VAC5-20-21) may be exempt from Table 45-3A for the period of time that the CARB ACP agreement remains in effect provided that all ACP products used for emission credits within the CARB ACP agreement are contained in Table 45-3A. A manufacturer claiming such an ACP agreement on this basis must submit to the board a copy of the CARB ACP decision (i.e., the executive order), including all conditions established by CARB applicable to the exemption and certification that the manufacturer will comply with the CARB ACP decision for those ACP products in the areas specified in 9VAC5-45-280 C.

B. Upon 90 days written notice, the board may require a responsible party to report information for a consumer product the board may specify, including, but not limited to, all or part of the following information:

1. The company name of the responsible party and the party's address, telephone number, and designated contact person.

2. A showing satisfactory to the board under 9VAC5-170-60 B and C that supports any claim of confidentiality made pursuant to 9VAC5-170-60, §§ 10.1-1314 and 10.1-1314.1 of the Virginia Air Pollution Control Law, and other applicable state confidentiality requirements.

3. The product brand name for each consumer product subject to registration and, upon request by the board, the product label.

6. An identification of each product brand name and form as a "Household Product," "I&I Product," or both.

7. Separate sales in pounds per year, to the nearest pound, and the method used to calculate sales for each product form.

8. For registrations submitted by two companies, an identification of the company that is submitting relevant data separate from that submitted by the responsible party. All registration information from both companies shall be submitted by the date specified in this subsection.

9. For each product brand name and form, the net percent by weight of the total product, less container and packaging, composed of the following, rounded to the nearest one-tenth of a percent (0.1%):

(2) The percent of fragrances that are all other carbon-containing compounds [ ~~; and~~ ].

10. For each product brand name and form, the identity, including the specific chemical name and associated Chemical Abstract Services (CAS) number, of the following:

C. In addition to the requirements of subdivision B 10 of this section, the responsible party shall report to the board the net percentage by weight of each ozone-depleting compound that is:

2. Contained in a product subject to registration under subsection B of this section in an amount greater than 1.0% by weight.

D. Information submitted by responsible parties pursuant to this section shall be available to the public except where the owner makes a showing satisfactory to the board under 9VAC5-170-60 B that the information meets the criteria in 9VAC5-170-60 C, in which case the information shall be handled in accordance with the procedures specified in §§ 10.1-1314 and 10.1-1314.1 of the Air Pollution Control Law of Virginia.

E. Provisions follow concerning special recordkeeping and reporting requirements for consumer products that contain perchloroethylene or methylene chloride.

1. The requirements of this subsection shall apply to all responsible parties for consumer products that are subject to 9VAC5-45-310 A and contain perchloroethylene or methylene chloride. For the purposes of this subsection, a product contains perchloroethylene or methylene chloride if the product contains 1.0% or more by weight (exclusive of the container or packaging) of either perchloroethylene or methylene chloride.

2. For each consumer product that contains perchloroethylene or methylene chloride, the responsible party shall keep records of the following information for products sold during each calendar year, beginning with the year of the applicable compliance date specified in 9VAC5-45-360, and ending with the year 2010:

a. The product brand name and a copy of the product label with legible usage instructions;

d. For each product form listed in subdivision 2 c of this subsection, the total sales during the calendar year to the nearest pound (exclusive of the container or packaging), and the method used for calculating sales;

e. The weight percentage, to the nearest 0.10% of perchloroethylene and methylene chloride in the consumer product;

3. Upon 90 days written notice, the board may require a responsible party to report the information specified in subdivision 2 of this subsection.

4. Records required by subdivision 2 of this subsection shall be maintained by the responsible party for three calendar years from the date such records were created.

5. Alternative control plan notifications, records, and reporting shall be made as required by 9VAC5-45-320 and as required in the ACP agreement.

6. Innovative product notifications, records, and reporting shall be made as required by 9VAC5-45-330 and as required in the innovative products exemption notification letter.

Article 4
Emission Standards for Consumer Products Manufactured on or after [ ~~May 1, 2010~~ ] August 1, 2010

A. Except as provided in 9VAC5-45-410, the provisions of this article apply to any consumer product manufactured on or after [ ~~May 1, 2010~~ ] August 1, 2010, that contains volatile organic compounds (VOCs). The provisions of Article 3 (9VAC5-45-280 et seq.) of this part apply to consumer products manufactured before [ ~~May 1, 2010~~ ] August 1, 2010.

B. Except as provided in 9VAC5-45-410, the provisions of this article apply to any owner or other person who sells, supplies, offers for sale or manufactures for sale any consumer product.

C. The provisions of this article apply to owners and other persons in the Northern Virginia ~~and~~, Fredericksburg, and Richmond Volatile Organic Compound Emissions Control Areas designated in 9VAC5-20-206.

D. For purposes of this article, the terms "supply" or "supplied" do not include internal transactions within a business or governmental entity. These terms only apply to transactions between manufacturers/commercial distributors that sell or otherwise provide products to businesses/governmental entities/individuals.

A. For the purpose of applying this article in the context of the Regulations for the Control and Abatement of Air Pollution and related uses, the words or terms shall have the meanings given them in subsection C of this section.

B. As used in this article, all terms not defined herein shall have the meanings given them in 9VAC5-10 (General Definitions), unless otherwise required by context.

"ACP" or "alternative control plan" means any emissions averaging program approved by the board pursuant to the provisions of this article.

"ACP agreement" means the document signed by the board that includes the conditions and requirements of the board and that allows manufacturers to sell ACP products pursuant to the requirements of this article.

"ACP emissions" means the sum of the VOC emissions from every ACP product subject to an ACP agreement approving an ACP, during the compliance period specified in the ACP agreement, expressed to the nearest pound of VOC and calculated according to the following equation:

"ACP limit" means the maximum allowable ACP emissions during the compliance period specified in an ACP agreement approving an ACP, expressed to the nearest pound of VOC, and calculated according to the following equation:

"ACP product" means any consumer product subject to the VOC standards specified in 9VAC5-45-430 A, except those products that have been exempted as innovative products under 9VAC5-45-450.

"ACP reformulation" or "ACP reformulated" means the process of reducing the VOC content of an ACP product within the period that an ACP is in effect to a level that is less than the current VOC content of the product.

"ACP standard" means either the ACP product's pre-ACP VOC content or the applicable VOC standard specified in 9VAC5-45-430 A, whichever is the lesser of the two.

"ACP VOC standard" means the maximum allowable VOC content for an ACP product, determined as follows:

1. The applicable VOC standard specified in 9VAC5-45-430 A for all ACP products except for charcoal lighter material;

2. For charcoal lighter material products only, the VOC standard for the purposes of this article shall be calculated according to the following equation:

0.020 = the certification emissions level for the product, as specified in9VAC5-45-430 E.

"Adhesive" means any product that is used to bond one surface to another by attachment. Adhesive does not include products used on humans and animals, adhesive tape, contact paper, wallpaper, shelf liners, or any other product with an adhesive incorporated onto or in an inert substrate. For contact adhesive only, adhesive also does not include units of product, less packaging, that consist of more than one gallon. In addition, for construction, panel, and floor covering adhesive and general purpose adhesive only, adhesive does not include units of product, less packaging, that weigh more than one pound and consist of more than 16 fluid ounces. The package size limitations do not apply to aerosol adhesives.

"Adhesive remover" means a product designed to remove adhesive from either a specific substrate or a variety of substrates. Adhesive remover does not include products that remove adhesives intended exclusively for use on humans or animals. For the purpose of this definition and the following adhesive remover subcategories in subdivisions 1 through 4 of this definition, adhesive shall mean a substance used to bond one or more materials. Adhesives include, but are not limited to, caulk, sealant, glue, or similar substances used for the purpose of forming a bond.

1. "Floor and wall covering adhesive remover" means a product designed or labeled to remove floor or wall coverings and associated adhesive from the underlying substrate.

2. "Gasket or thread locking adhesive remover" means a product designed or labeled to remove gaskets or thread locking adhesives. Products labeled for dual use as a paint stripper and as a gasket remover or thread locking adhesive remover are considered gasket or thread locking adhesive remover.

3. "General purpose adhesive remover" means a product designed or labeled to remove cyanoacrylate adhesives and nonreactive adhesives or residue from a variety of substrates. General purpose adhesive remover includes, but is not limited to, products that remove thermoplastic adhesives, pressure sensitive adhesives, dextrin-based or starch-based adhesives, casein glues, rubber-based or latex-based adhesives, as well as products that remove stickers, decals, stencils, or similar materials. General purpose adhesive remover does not include floor or wall covering adhesive remover.

4. "Specialty adhesive remover" means a product designed to remove reactive adhesives from a variety of substrates. Reactive adhesives include adhesives that require a hardener or catalyst in order for the bond to occur. Examples of reactive adhesives include, but are not limited to, epoxies, urethanes, and silicones. Specialty adhesive remover does not include gasket or thread locking adhesive remover.

"Aerosol adhesive" means an aerosol product in which the spray mechanism is permanently housed in a nonrefillable can designed for hand-held application without the need for ancillary hoses or spray equipment. Aerosol adhesives include special purpose spray adhesives, mist spray adhesives, and web spray adhesives.

"Aerosol cooking spray" means any aerosol product designed either to reduce sticking on cooking and baking surfaces or to be applied on food, or both.

"Aerosol product" means a pressurized spray system that dispenses product ingredients by means of a propellant contained in a product or a product's carrier, or by means of a mechanically induced force. Aerosol product does not include pump sprays.

"Agricultural use" means the use of any pesticide or method or device for the control of pests in connection with the commercial production, storage, or processing of any animal or plant crop. Agricultural use does not include the sale or use of pesticides in properly labeled packages or containers that are intended for home use, use in structural pest control, industrial use, or institutional use. For the purposes of this definition only:

2. "Industrial use" means use for or in a manufacturing, mining, or chemical process or use in the operation of factories, processing plants, and similar sites.

3. "Institutional use" means use within the perimeter of, or on property necessary for the operation of, buildings such as hospitals, schools, libraries, auditoriums, and office complexes.

4. "Structural pest control" means a use requiring a license under the applicable state pesticide licensing requirement.

"Air freshener" means any consumer product including, but not limited to, sprays, wicks, powders, and crystals, designed for the purpose of masking odors or freshening, cleaning, scenting, or deodorizing the air. Air fresheners do not include products that are used on the human body, products that function primarily as cleaning products (as indicated on a product label) or as toilet/urinal care products, disinfectant products claiming to deodorize by killing germs on surfaces, or institutional or industrial disinfectants when offered for sale solely through institutional and industrial channels of distribution. Air fresheners do include spray disinfectants and other products that are expressly represented for use as air fresheners, except institutional and industrial disinfectants when offered for sale through institutional and industrial channels of distribution. To determine whether a product is an air freshener, all verbal and visual representations regarding product use on the label or packaging and in the product's literature and advertising may be considered. The presence of, and representations about, a product's fragrance and ability to deodorize (resulting from surface application) shall not constitute a claim of air freshening.

"All other carbon-containing compounds" means all other compounds that contain at least one carbon atom and are not an "exempt compound" or an "LVP-VOC."

"All other forms" means all consumer product forms for which no form-specific VOC standard is specified. Unless specified otherwise by the applicable VOC standard, all other forms include, but are not limited to, solids, liquids, wicks, powders, crystals, and cloth or paper wipes (towelettes).

"Alternative control plan" or "ACP" means any emissions averaging program approved by the board pursuant to the provisions of this article.

"Antimicrobial hand or body cleaner or soap" means a cleaner or soap that is designed to reduce the level of microorganisms on the skin through germicidal activity. Antimicrobial hand or body cleaner or soap includes, but is not limited to, antimicrobial hand or body washes or cleaners, food handler hand washes, healthcare personnel hand washes, pre-operative skin preparations, and surgical scrubs. Antimicrobial hand or body cleaner or soap does not include prescription drug products, antiperspirants, astringent or toner, deodorant, facial cleaner or soap, general-use hand or body cleaner or soap, hand dishwashing detergent (including antimicrobial), heavy-duty hand cleaner or soap, medicated astringent or medicated toner, and rubbing alcohol.

"Antiperspirant" means any product including, but not limited to, aerosols, roll-ons, sticks, pumps, pads, creams, and squeeze-bottles, that is intended by the manufacturer to be used to reduce perspiration in the human axilla by at least 20% in at least 50% of a target population.

"Anti-static product" means a product that is labeled to eliminate, prevent, or inhibit the accumulation of static electricity. Anti-static products do not include electronic cleaners, floor polish or waxes, floor coatings, and products that meet the definition of aerosol coating products or architectural coatings.

"Architectural coating" means a coating applied to stationary structures and their appurtenances, to mobile homes, to pavements, or to curbs.

"Astringent or toner" means any product not regulated as a drug by the United States Food and Drug Administration that is applied to the skin for the purpose of cleaning or tightening pores. This category also includes clarifiers and substrate-impregnated products. This category does not include any hand, face, or body cleaner or soap product, medicated astringent or medicated toner, cold cream, lotion, or antiperspirant.

"Automotive brake cleaner" means a cleaning product designed to remove oil, grease, brake fluid, brake pad material, or dirt from motor vehicle brake mechanisms.

"Automotive instant detailer" means a product designed for use in a pump spray that is applied to the painted surface of automobiles and wiped off prior to the product being allowed to dry.

"Automotive rubbing or polishing compound" means a product designed primarily to remove oxidation, old paint, scratches or swirl marks, and other defects from the painted surfaces of motor vehicles without leaving a protective barrier.

"Automotive wax, polish, sealant, or glaze" means a product designed to seal out moisture, increase gloss, or otherwise enhance a motor vehicle's painted surfaces. Automotive wax, polish, sealant, or glaze includes, but is not limited to, products designed for use in auto body repair shops and drive-through car washes, as well as products designed for the general public. Automotive wax, polish, sealant, or glaze does not include automotive rubbing or polishing compounds, automotive wash and wax products, surfactant-containing car wash products, and products designed for use on unpainted surfaces such as bare metal, chrome, glass, or plastic.

"Automotive windshield washer fluid" means any liquid designed for use in a motor vehicle windshield washer system either as an antifreeze or for the purpose of cleaning, washing, or wetting the windshield. Automotive windshield washer fluid also includes liquids that are (i) packaged as a pre-wetted, single-use manual wipe and (ii) designed exclusively for cleaning, washing, or wetting automotive glass surfaces for the purpose of restoring or maintaining visibility for the driver. Glass cleaners that are intended for use on other glass surfaces are not included in this definition. Automotive windshield washer fluid does not include fluids placed by the manufacturer in a new vehicle.

"Bathroom and tile cleaner" means a product designed to clean tile or surfaces in bathrooms. Bathroom and tile cleaners do not include products designed primarily to clean toilet bowls, toilet tanks, or urinals.

"Bug and tar remover" means a product labeled to remove either or both of the following from painted motor vehicle surfaces without causing damage to the finish: (i) biological residues, such as insect carcasses and tree sap, and (ii) road grime, such as road tar, roadway paint markings, and asphalt.

"Carburetor or fuel-injection air intake cleaner" means a product designed to remove fuel deposits, dirt, or other contaminants from a carburetor, choke, throttle body of a fuel-injection system, or associated linkages. Carburetor or fuel-injection air intake cleaner does not include products designed exclusively to be introduced directly into the fuel lines or fuel storage tank prior to introduction into the carburetor or fuel injectors.

"Carpet and upholstery cleaner" means a cleaning product designed for the purpose of eliminating dirt and stains on rugs, carpeting, and the interior of motor vehicles or on household furniture or objects upholstered or covered with fabrics such as wool, cotton, nylon, or other synthetic fabrics. Carpet and upholstery cleaners include, but are not limited to, products that make fabric protectant claims. Carpet and upholstery cleaners do not include general purpose cleaners, spot removers, vinyl or leather cleaners, dry cleaning fluids, or products designed exclusively for use at industrial facilities engaged in furniture or carpet manufacturing.

"Certified emissions" means the emissions level for products approved under 9VAC5-45-430 E, as determined pursuant to South Coast Air Quality Management District Rule 1174 Ignition Method Compliance Certification Protocol (see 9VAC5-20-21), expressed to the nearest 0.001 pound VOC per start.

"Certified use rate" means the usage level for products approved under 9VAC5-45-430 E, as determined pursuant to South Coast Air Quality Management District Rule 1174 Ignition Method Compliance Certification Protocol (see 9VAC5-20-21), expressed to the nearest 0.001 pound certified product used per start.

"Charcoal lighter material" means any combustible material designed to be applied on, incorporated in, added to, or used with charcoal to enhance ignition. Charcoal lighter material does not include any of the following:

"Colorant" means any pigment or coloring material used in a consumer product for an aesthetic effect or to dramatize an ingredient.

"Compliance period" means the period of time, not to exceed one year, for which the ACP limit and ACP emissions are calculated and for which compliance with the ACP limit is determined, as specified in the ACP agreement approving an ACP.

"Construction, panel, and floor covering adhesive" means any one-component adhesive that is designed exclusively for the installation, remodeling, maintenance, or repair of:

1. Structural and building components that include, but are not limited to, beams, trusses, studs, paneling (drywall or drywall laminates, fiberglass reinforced plastic (FRP), plywood, particle board, insulation board, predecorated hardboard or tileboard, etc.), ceiling and acoustical tile, molding, fixtures, countertops or countertop laminates, cove or wall bases, and flooring or subflooring; or

2. Floor or wall coverings that include, but are not limited to, wood or simulated wood covering, carpet, carpet pad or cushion, vinyl-backed carpet, flexible flooring material, nonresilient flooring material, mirror tiles and other types of tiles, and artificial grass.

Construction, panel, and floor covering adhesive does not include floor seam sealer.

"Consumer" means a person who purchases or acquires a consumer product for personal, family, household, or institutional use. Persons acquiring a consumer product for resale are not consumers for that product.

"Consumer product" means a chemically formulated product used by household and institutional consumers including, but not limited to, detergents; cleaning compounds; polishes; floor finishes; cosmetics; personal care products; home, lawn, and garden products; disinfectants; sanitizers; aerosol paints; and automotive specialty products, but does not include other paint products, furniture coatings, or architectural coatings. As used in this article, consumer products shall also refer to aerosol adhesives, including aerosol adhesives used for consumer, industrial, or commercial uses.

2. Is allowed to dry before the two surfaces are placed in contact with each other;

3. Forms an immediate bond that is impossible, or difficult, to reposition after both adhesive-coated surfaces are placed in contact with each other; and

4. Does not need sustained pressure or clamping of surfaces after the adhesive-coated surfaces have been brought together using sufficient momentary pressure to establish full contact between both surfaces.

Contact adhesive does not include rubber cements that are primarily intended for use on paper substrates. Contact adhesive also does not include vulcanizing fluids that are designed and labeled for tire repair only.

"Contact adhesive - general purpose" means any contact adhesive that is not a contact adhesive - special purpose.

"Contact adhesive - special purpose" means a contact adhesive that is used as follows:

1. To bond melamine-covered board, unprimed metal, unsupported vinyl, Teflon®, ultra-high molecular weight polyethylene, rubber, high pressure laminate or wood veneer 1/16 inch or less in thickness to any porous or nonporous surface, and is sold in units of product, less packaging, that contain more than eight fluid ounces; or

a. Automotive under-the-hood applications requiring heat, oil, or gasoline resistance; or

"Container or packaging" means the part or parts of the consumer or institutional product that serve only to contain, enclose, incorporate, deliver, dispense, wrap, or store the chemically formulated substance or mixture of substances that is solely responsible for accomplishing the purposes for which the product was designed or intended. Containers or packaging include any article onto or into which the principal display panel and other accompanying literature or graphics are incorporated, etched, printed, or attached.

"Contact person" means a representative that has been designated by the responsible ACP party for the purpose of reporting or maintaining information specified in the ACP agreement approving an ACP.

"Crawling bug insecticide" means an insecticide product that is designed for use against ants, cockroaches, or other household crawling arthropods, including, but not limited to, mites, silverfish or spiders. Crawling bug insecticide does not include products designed to be used exclusively on humans or animals or a house dust mite product. For the purposes of this definition only:

1. "House dust mite product" means a product whose label, packaging, or accompanying literature states that the product is suitable for use against house dust mites, but does not indicate that the product is suitable for use against ants, cockroaches, or other household crawling arthropods.

2. "House dust mite" means mites that feed primarily on skin cells shed in the home by humans and pets and that belong to the phylum Arthropoda, the subphylum Chelicerata, the class Arachnida, the subclass Acari, the order Astigmata, and the family Pyroglyphidae.

"Date-code" means the day, month, and year on which the consumer product was manufactured, filled, or packaged, or a code indicating such a date.

"Deodorant" means any product including, but not limited to, aerosols, roll-ons, sticks, pumps, pads, creams, and squeeze-bottles, that indicates or depicts on the container or packaging, or on any sticker or label affixed thereto, that the product can be used on or applied to the human axilla to provide a scent or minimize odor. A deodorant body spray product that indicates or depicts on the container or packaging, or on any sticker or label affixed thereto, that it can be used on or applied to the human axilla, is a deodorant.

"Deodorant body spray" means a personal fragrance product with 20% or less fragrance that is designed for application all over the human body to provide a scent. A deodorant body spray product that indicates or depicts on the container or packaging, or on any sticker or label affixed thereto, that it can be used on or applied to the human axilla, is a deodorant.

"Device" means an instrument or contrivance (other than a firearm) that is designed for trapping, destroying, repelling, or mitigating a pest or other form of plant or animal life (other than human and other than bacterium, virus, or another microorganism on or in living humans or other living animals); but not including equipment used for the application of pesticides when sold separately therefrom.

"Disinfectant" means a product intended to destroy or irreversibly inactivate infectious or other undesirable bacteria, pathogenic fungi, or viruses on surfaces or inanimate objects and whose label is registered under the FIFRA. Disinfectant does not include any of the following:

3. Products designed solely for use in swimming pools, therapeutic tubs, or hot tubs; or

4. Products that, as indicated on the principal display panel or label, are designed primarily for use as bathroom and tile cleaners, glass cleaners, general purpose cleaners, toilet bowl cleaners, or metal polishes.

"Distributor" means a person to whom a consumer product is sold or supplied for the purposes of resale or distribution in commerce, except that manufacturers, retailers, and consumers are not distributors.

"Double phase aerosol air freshener" means an aerosol air freshener with the liquid contents in two or more distinct phases that require the product container to be shaken before use to mix the phases, producing an emulsion.

"Dry cleaning fluid" means a nonaqueous liquid product designed and labeled exclusively for use on:

1. Fabrics that are labeled "for dry clean only," such as clothing or drapery; or

Dry cleaning fluid includes, but is not limited to, those products used by commercial dry cleaners and commercial businesses that clean fabrics such as draperies at the customer's residence or work place. Dry cleaning fluid does not include spot remover or carpet and upholstery cleaner. For the purposes of this definition, "S-coded fabric" means an upholstery fabric designed to be cleaned only with water-free spot cleaning products as specified by the American Furniture Manufacturers Association Joint Industry Fabrics Standards Committee, Woven and Knit Residential Upholstery Fabric Standards and Guidelines (see 9VAC5-20-21).

"Dusting aid" means a product designed to assist in removing dust and other soils from floors and other surfaces without leaving a wax or silicone-based coating. Dusting aid does not include pressurized gas dusters.

"Electrical cleaner" means a product labeled to remove heavy soils such as grease, grime, or oil from electrical equipment, including, but not limited to, electric motors, armatures, relays, electric panels, or generators. Electrical cleaner does not include general purpose cleaners, general purpose degreasers, dusting aids, electronic cleaners, energized electrical cleaners, pressurized gas dusters, engine degreasers, anti-static products, or products designed to clean the casings or housings of electrical equipment.

"Electronic cleaner" means a product labeled for the removal of dirt, moisture, dust, flux or oxides from the internal components of electronic or precision equipment such as circuit boards, and the internal components of electronic devices, including but not limited to, radios, compact disc (CD) players, digital video disc (DVD) players, and computers. Electronic cleaner does not include general purpose cleaners, general purpose degreasers, dusting aids, pressurized gas dusters, engine degreasers, electrical cleaners, energized electrical cleaners, anti-static products, or products designed to clean the casings or housings of electronic equipment.

"Energized electrical cleaner" means a product that meets both of the following criteria:

1. The product is labeled to clean or degrease electrical equipment, where cleaning or degreasing is accomplished when electrical current exists, or when there is a residual electrical potential from a component, such as a capacitor;

2. The product label clearly displays the statements: "Energized equipment use only. Not to be used for motorized vehicle maintenance, or their parts."

"Enforceable sales" means the total amount of an ACP product sold for use in the applicable volatile organic compound emissions control areas designated in 9VAC5-45-400 C during the applicable compliance period specified in the ACP agreement approving an ACP, as determined through enforceable sales records (expressed to the nearest pound, excluding product container and packaging).

"Enforceable sales record" means a written, point-of-sale record or another board-approved system of documentation from which the mass, in pounds (less product container and packaging), of an ACP product sold to the end user in the applicable volatile organic compound emissions control areas designated in 9VAC5-45-400 C during the applicable compliance period can be accurately documented. For the purposes of this article, enforceable sales records include, but are not limited to, the following types of records:

1. Accurate records of direct retail or other outlet sales to the end user during the applicable compliance period;

2. Accurate compilations, made by independent market surveying services, of direct retail or other outlet sales to the end users for the applicable compliance period, provided that a detailed method that can be used to verify data composing such summaries is submitted by the responsible ACP party and approved by the board; and

"Engine degreaser" means a cleaning product designed to remove grease, grime, oil, and other contaminants from the external surfaces of engines and other mechanical parts.

"Exempt compound" means acetone, ethane, methyl acetate, parachlorobenzotrifluoride (1-chloro-4-trifluoromethyl benzene), or perchloroethylene (tetrachloroethylene).

"Existing product" means any formulation of the same product category and form sold, supplied, manufactured, or offered for sale prior to March 9, 2005, or any subsequently introduced identical formulation.

"Fabric protectant" means a product designed to be applied to fabric substrates to protect the surface from soiling from dirt and other impurities or to reduce absorption of liquid into the fabric's fibers. Fabric protectant does not include waterproofers, products designed for use solely on leather, or products designed for use solely on fabrics that are labeled "for dry clean only" and sold in containers of 10 fluid ounces or less.

"Fabric refresher" means a product labeled to neutralize or eliminate odors on nonlaundered fabric including, but not limited to, soft household surfaces, rugs, carpeting, draperies, bedding, automotive interiors, footwear, athletic equipment, clothing or on household furniture or objects upholstered or covered with fabrics such as, but not limited to, wool, cotton, or nylon. Fabric refresher does not include anti-static products, carpet and upholstery cleaners, soft household surface sanitizers, footwear or leather care products, spot removers, or disinfectants, or products labeled for application to both fabric and human skin. For the purposes of this definition only, soft household surface sanitizer means a product labeled to neutralize or eliminate odors on surfaces listed above whose label is registered as a sanitizer under FIFRA.

"Facial cleaner or soap" means a cleaner or soap designed primarily to clean the face. Facial cleaner or soap includes, but is not limited to, facial cleansing creams, semisolids, liquids, lotions, and substrate-impregnated forms. Facial cleaner or soap does not include prescription drug products, antimicrobial hand or body cleaner or soap, astringent or toner, general-use hand or body cleaner or soap, medicated astringent or medicated toner, or rubbing alcohol.

"Fat wood" means pieces of wood kindling with high [ ~~naturally-occurring~~ naturally occurring ] levels of sap or resin that enhance ignition of the kindling. Fat wood does not include kindling with substances added to enhance flammability, such as wax-covered or wax-impregnated wood-based products.

"FIFRA" means the Federal Insecticide, Fungicide, and Rodenticide Act (7 USC § 136-136y).

"Flea and tick insecticide" means an insecticide product that is designed for use against fleas, ticks, their larvae, or their eggs. Flea and tick insecticide does not include products that are designed to be used exclusively on humans or animals and their bedding.

"Flexible flooring material" means asphalt, cork, linoleum, no-wax, rubber, seamless vinyl, and vinyl composite flooring.

"Floor coating" means an opaque coating that is labeled and designed for application to flooring, including but not limited to, decks, porches, steps, and other horizontal surfaces that may be subject to foot traffic.

"Floor polish or wax" means a wax, polish, or other product designed to polish, protect, or enhance floor surfaces by leaving a protective coating that is designed to be periodically replenished. Floor polish or wax does not include spray buff products, products designed solely for the purpose of cleaning floors, floor finish strippers, products designed for unfinished wood floors, and coatings subject to architectural coatings regulations.

"Floor seam sealer" means a product designed and labeled exclusively for bonding, fusing, or sealing (coating) seams between adjoining rolls of installed flexible sheet flooring.

"Floor wax stripper" means a product designed to remove natural or synthetic floor polishes or waxes through breakdown of the polish or wax polymers or by dissolving or emulsifying the polish or wax. Floor wax stripper does not include aerosol floor wax strippers or products designed to remove floor wax solely through abrasion.

"Flying bug insecticide" means an insecticide product that is designed for use against flying insects or other flying arthropods, including but not limited to flies, mosquitoes, moths, or gnats. Flying bug insecticide does not include wasp and hornet insecticide, products that are designed to be used exclusively on humans or animals, or a moth-proofing product. For the purposes of this definition only, "moth-proofing product" means a product whose label, packaging, or accompanying literature indicates that the product is designed to protect fabrics from damage by moths, but does not indicate that the product is suitable for use against flying insects or other flying arthropods.

"Footwear or leather care product" means any product designed or labeled to be applied to footwear or to other leather articles or components, to maintain, enhance, clean, protect, or modify the appearance, durability, fit, or flexibility of the footwear, leather article or component. Footwear includes both leather and nonleather foot apparel. Footwear or leather care product does not include fabric protectants; general purpose adhesives; contact adhesives; vinyl/fabric/leather/polycarbonate coatings; rubber and vinyl protectants; fabric refreshers; products solely for deodorizing; or sealant products with adhesive properties used to create external protective layers greater than 2 millimeters thick.

"Fragrance" means a substance or complex mixture of aroma chemicals, natural essential oils, and other functional components with a combined vapor pressure not in excess of 2 mm of Hg at 20ºC, the sole purpose of which is to impart an odor or scent, or to counteract a malodor.

"Furniture coating" means a paint designed for application to room furnishings including, but not limited to, cabinets (kitchen, bath and vanity), tables, chairs, beds, and sofas.

"Furniture maintenance product" means a wax, polish, conditioner, or other product designed for the purpose of polishing, protecting, or enhancing finished wood surfaces other than floors. Furniture maintenance products do not include dusting aids, wood cleaners and products designed solely for the purpose of cleaning, and products designed to leave a permanent finish such as stains, sanding sealers, and lacquers.

"Gel" means a colloid in which the disperse phase has combined with the continuous phase to produce a semisolid material, such as jelly.

"General purpose adhesive" means a nonaerosol adhesive designed for use on a variety of substrates. General purpose adhesive does not include:

3. Adhesives designed exclusively for application on one specific category of substrates (i.e., substrates that are composed of similar materials, such as different types of metals, paper products, ceramics, plastics, rubbers, or vinyls); or

4. Adhesives designed exclusively for use on one specific category of articles (i.e., articles that may be composed of different materials but perform a specific function, such as gaskets, automotive trim, weather-stripping, or carpets).

"General purpose cleaner" means a product designed for general all-purpose cleaning, in contrast to cleaning products designed to clean specific substrates in certain situations. General purpose cleaner includes products designed for general floor cleaning, kitchen or countertop cleaning, and cleaners designed to be used on a variety of hard surfaces and does not include general purpose degreasers and electronic cleaners.

"General purpose degreaser" means a product labeled to remove or dissolve grease, grime, oil, and other oil-based contaminants from a variety of substrates, including automotive or miscellaneous metallic parts. General purpose degreaser does not include engine degreaser, general purpose cleaner, adhesive remover, electronic cleaner, electrical cleaner, energized electrical cleaner, metal polish or cleanser, products used exclusively in solvent cleaning tanks or related equipment, or products that are (i) sold exclusively to establishments that manufacture or construct goods or commodities; and (ii) labeled "not for retail sale." Solvent cleaning tanks or related equipment includes, but is not limited to, cold cleaners, vapor degreasers, conveyorized degreasers, film cleaning machines, or products designed to clean miscellaneous metallic parts by immersion in a container.

"General-use hand or body cleaner or soap" means a cleaner or soap designed to be used routinely on the skin to clean or remove typical or common dirt and soils. General-use hand or body cleaner or soap includes, but is not limited to, hand or body washes, dual-purpose shampoo-body cleaners, shower or bath gels, and moisturizing cleaners or soaps. General-use hand or body cleaner or soap does not include prescription drug products, antimicrobial hand or body cleaner or soap, astringent or toner, facial cleaner or soap, hand dishwashing detergent (including antimicrobial), heavy-duty hand cleaner or soap, medicated astringent or medicated toner, or rubbing alcohol.

"Glass cleaner" means a cleaning product designed primarily for cleaning surfaces made of glass. Glass cleaner does not include products designed solely for the purpose of cleaning optical materials used in eyeglasses, photographic equipment, scientific equipment, and photocopying machines.

"Graffiti remover" means a product labeled to remove spray paint, ink, marker, crayon, lipstick, nail polish, or shoe polish, from a variety of noncloth or nonfabric substrates. Graffiti remover does not include paint remover or stripper, nail polish remover, or spot remover. Products labeled for dual use as both a paint stripper and graffiti remover are considered graffiti removers.

"Gross sales" means the estimated total sales of an ACP product in the applicable volatile organic compound emissions control areas designated in 9VAC5-45-400 C during a specific compliance period (expressed to the nearest pound), based on either of the following methods, whichever the responsible ACP party demonstrates to the satisfaction of the board will provide an accurate sales estimate:

1. Apportionment of national or regional sales of the ACP product to sales, determined by multiplying the average national or regional sales of the product by the fraction of the national or regional population, respectively, that is represented by the current population of the applicable volatile organic compound emissions control areas designated in 9VAC5-45-400 C; or

2. Another documented method that provides an accurate estimate of the total current sales of the ACP product.

"Hair mousse" means a hairstyling foam designed to facilitate styling of a coiffure and provide limited holding power.

"Hair shine" means a product designed for the primary purpose of creating a shine when applied to the hair. Hair shine includes, but is not limited to, dual-use products designed primarily to impart a sheen to the hair. Hair shine does not include hair spray, hair mousse, hair styling product, hair styling gel, or products whose primary purpose is to condition or hold the hair.

"Hair spray" means a consumer product that is applied to styled hair, and is designed or labeled to provide sufficient rigidity to hold, retain and/or finish the style of the hair for a period of time. Hair spray includes aerosol hair sprays, pump hair sprays, spray waxes; color, glitter, or sparkle hairsprays that make finishing claims; and products that are both a styling and finishing product. Hair spray does not include spray products that are intended to aid in styling but does not provide finishing of a hairstyle. For the purposes of this article, "finish" or "finishing" means the maintaining or holding of previously styled hair for a period of time. For the purposes of this article, "styling" means the forming, sculpting, or manipulating the hair to temporarily alter the hair's shape.

"Hair styling product" means a consumer product that is designed or labeled for the application to wet, damp or dry hair to aid in defining, shaping, lifting, styling and or sculpting of the hair. Hair styling product includes, but is not limited to hair balm; clay; cream; creme; curl straightener; gel; liquid; lotion; paste; pomade; putty; root lifter; serum; spray gel; stick; temporary hair straightener; wax; spray products that aid in styling but do not provide finishing of a hairstyle; and leave-in volumizers, detanglers or conditioners that make styling claims. Hair styling product does not include hair mousse, hair shine, hair spray, or shampoos or conditioners that are rinsed from the hair prior to styling. For the purposes of this article, "finish" or "finishing" means the maintaining or holding of previously styled hair for a period of time. For the purposes of this article, "styling" means the forming, sculpting, or manipulating the hair to temporarily alter the hair's shape.

"Heavy-duty hand cleaner or soap" means a product designed to clean or remove difficult dirt and soils such as oil, grease, grime, tar, shellac, putty, printer's ink, paint, graphite, cement, carbon, asphalt, or adhesives from the hand with or without the use of water. Heavy-duty hand cleaner or soap does not include prescription drug products, antimicrobial hand or body cleaner or soap, astringent or toner, facial cleaner or soap, general-use hand or body cleaner or soap, medicated astringent or medicated toner, or rubbing alcohol.

"Herbicide" means a pesticide product designed to kill or retard a plant's growth, but excludes products that are (i) for agricultural use, or (ii) restricted materials that require a permit for use and possession.

"High volatility organic compound" or "HVOC" means a volatile organic compound that exerts a vapor pressure greater than 80 millimeters of mercury (mm Hg) when measured at 20ºC.

"Household product" means a consumer product that is primarily designed to be used inside or outside of living quarters or residences that are occupied or intended for occupation by people, including the immediate surroundings.

"Insecticide" means a pesticide product that is designed for use against insects or other arthropods, but excluding products that are:

2. For a use that requires a structural pest control license under applicable state laws or regulations; or

3. Materials classified for restricted use pursuant to 40 CFR 152.75 and require a pesticide business license from the Virginia Pesticide Control Board pursuant to 2VAC20-40-20 for use and possession.

"Insecticide fogger" means an insecticide product designed to release all or most of its content as a fog or mist into indoor areas during a single application.

"Institutional product" or "industrial and institutional (I&I) product" means a consumer product that is designed for use in the maintenance or operation of an establishment that:

1. Manufactures, transports, or sells goods or commodities, or provides services for profit; or

2. Is engaged in the nonprofit promotion of a particular public, educational, or charitable cause.

Establishments include, but are not limited to, government agencies, factories, schools, hospitals, sanitariums, prisons, restaurants, hotels, stores, automobile service and parts centers, health clubs, theaters, or transportation companies. Institutional product does not include household products and products that are incorporated into or used exclusively in the manufacture or construction of the goods or commodities at the site of the establishment.

"Label" means written, printed, or graphic matter affixed to, applied to, attached to, blown into, formed, molded into, embossed on, or appearing upon a consumer product or consumer product package, for purposes of branding, identifying, or giving information with respect to the product or to the contents of the package.

"Laundry prewash" means a product that is designed for application to a fabric prior to laundering and that supplements and contributes to the effectiveness of laundry detergents or provides specialized performance.

"Laundry starch product" means a product that is designed for application to a fabric, either during or after laundering, to impart and prolong a crisp, fresh look and may also act to help ease ironing of the fabric. Laundry starch product includes, but is not limited to, fabric finish, sizing, and starch.

"Lawn and garden insecticide" means an insecticide product labeled primarily to be used in household lawn and garden areas to protect plants from insects or other arthropods. Notwithstanding the requirements of 9VAC5-45-460 C, aerosol lawn and garden insecticides may claim to kill insects or other arthropods.

"Liquid" means a substance or mixture of substances that is capable of a visually detectable flow as determined under ASTM "Standard Test Method for Determining Whether a Material is a Liquid or a Solid" (see 9VAC5-20-21). Liquid does not include powders or other materials that are composed entirely of solid particles.

"Lubricant" means a product designed to reduce friction, heat, noise, or wear between moving parts, or to loosen rusted or immovable parts or mechanisms. Lubricant does not include automotive power steering fluids; products for use inside power generating motors, engines, and turbines, and their associated power-transfer gearboxes; two-cycle oils or other products designed to be added to fuels; products for use on the human body or animals; or products that are:

1. Sold exclusively to establishments that manufacture or construct goods or commodities; and

"LVP content" means the total weight, in pounds, of LVP-VOC in an ACP product multiplied by 100 and divided by the product's total net weight (in pounds, excluding container and packaging), expressed to the nearest 0.1.

"LVP-VOC" means a chemical compound or mixture that contains at least one carbon atom and meets one of the following:

1. Has a vapor pressure less than 0.1 mm Hg at 20ºC, as determined by CARB Method 310 (see 9VAC5-20-21);

2. Is a chemical compound with more than 12 carbon atoms, or a chemical mixture composed solely of compounds with more than 12 carbon atoms as verified by formulation data, and the vapor pressure and boiling point are unknown;

3. Is a chemical compound with a boiling point greater than 216ºC, as determined by CARB Method 310 (see 9VAC5-20-21); or

4. Is the weight percent of a chemical mixture that boils above 216ºC, as determined by CARB Method 310 (see 9VAC5-20-21).

For the purposes of the definition of LVP-VOC, "chemical compound" means a molecule of definite chemical formula and isomeric structure, and "chemical mixture" means a substrate composed of two or more chemical compounds.

"Manufacturer" means a person who imports, manufactures, assembles, produces, packages, repackages, or relabels a consumer product.

"Medicated astringent or medicated toner" means a product regulated as a drug by the United States Food and Drug Administration that is applied to the skin for the purpose of cleaning or tightening pores. Medicated astringent or medicated toner includes, but is not limited to, clarifiers and substrate-impregnated products. Medicated astringent or medicated toner does not include hand, face, or body cleaner or soap products, astringent or toner, cold cream, lotion, antiperspirants, or products that must be purchased with a doctor's prescription.

"Medium volatility organic compound" or "MVOC" means a volatile organic compound that exerts a vapor pressure greater than 2 mm Hg and less than or equal to 80 mm Hg when measured at 20ºC.

"Metal polish or cleanser" means a product designed primarily to improve the appearance of finished metal, metallic, or metallized surfaces by physical or chemical action. To "improve the appearance" means to remove or reduce stains, impurities, or oxidation from surfaces or to make surfaces smooth and shiny. Metal polish or cleanser includes, but is not limited to, metal polishes used on brass, silver, chrome, copper, stainless steel, and other ornamental metals. Metal polish or cleanser does not include automotive wax, polish, sealant, or glaze, wheel cleaner, paint remover or stripper, products designed and labeled exclusively for automotive and marine detailing, or products designed for use in degreasing tanks.

"Missing data days" means the number of days in a compliance period for which the responsible ACP party has failed to provide the required enforceable sales or VOC content data to the board, as specified in the ACP agreement.

"Mist spray adhesive" means an aerosol that is not a special purpose spray adhesive and that delivers a particle or mist spray, resulting in the formation of fine, discrete particles that yield a generally uniform and smooth application of adhesive to the substrate.

1. Designed and labeled to provide lubricity by depositing a thin film of graphite, molybdenum disulfide ("moly"), or polytetrafluoroethylene or closely related fluoropolymer ("teflon") on surfaces; and

2. Designed for general purpose lubrication, or for use in a wide variety of applications.

"Multipurpose lubricant" means a lubricant designed for general purpose lubrication, or for use in a wide variety of applications. Multipurpose lubricant does not include multipurpose dry lubricants, penetrants, or silicone-based multipurpose lubricants.

"Multipurpose solvent" means an organic liquid designed to be used for a variety of purposes, including cleaning or degreasing of a variety of substrates, or thinning, dispersing, or dissolving other organic materials. Multipurpose solvent includes solvents used in institutional facilities, except for laboratory reagents used in analytical, educational, research, scientific, or other laboratories. Multipurpose solvent does not include solvents used in cold cleaners, vapor degreasers, conveyorized degreasers or film cleaning machines, or solvents that are incorporated into, or used exclusively in the manufacture or construction of, the goods or commodities at the site of the establishment.

"Nail polish" means a clear or colored coating designed for application to the fingernails or toenails and including but not limited to, lacquers, enamels, acrylics, base coats, and top coats.

"Nail polish remover" means a product designed to remove nail polish and coatings from fingernails or toenails.

"Nonaerosol product" means a consumer product that is not dispensed by a pressurized spray system.

"Noncarbon containing compound" means a compound that does not contain carbon atoms.

"Nonresilient flooring" means flooring of a mineral content that is not flexible. Nonresilient flooring includes but is not limited to terrazzo, marble, slate, granite, brick, stone, ceramic tile, and concrete.

"Nonselective terrestrial herbicide" means a terrestrial herbicide product that is toxic to plants without regard to species.

"One-product business" means a responsible ACP party that sells, supplies, offers for sale, or manufactures for use in the applicable volatile organic compound emissions control areas designated in 9VAC5-45-400:

1. Only one distinct ACP product, sold under one product brand name, which is subject to the requirements of 9VAC5-45-430; or

2. Only one distinct ACP product line subject to the requirements of 9VAC5-45-430, in which all the ACP products belong to the same product category and the VOC contents in the products are within 98.0% and 102.0% of the arithmetic mean of the VOC contents over the entire product line.

"Oven cleaner" means a cleaning product designed to clean and to remove dried food deposits from oven walls.

"Paint" means a pigmented liquid, liquefiable, or mastic composition designed for application to a substrate in a thin layer that is converted to an opaque solid film after application and is used for protection, decoration or identification, or to serve some functional purpose such as the filling or concealing of surface irregularities or the modification of light and heat radiation characteristics.

"Paint remover or stripper" means a product designed to strip or remove paints or other related coatings, by chemical action, from a substrate without markedly affecting the substrate. Paint remover or stripper does not include multipurpose solvents, paint brush cleaners, products designed and labeled exclusively as graffiti removers, and hand cleaner products that claim to remove paints and other related coatings from skin.

"Penetrant" means a lubricant designed and labeled primarily to loosen metal parts that have bonded together due to rusting, oxidation, or other causes. Penetrant does not include multipurpose lubricants that claim to have penetrating qualities but are not labeled primarily to loosen bonded parts.

"Personal fragrance product" means any product that is applied to the human body or clothing for the primary purpose of adding a scent or masking a malodor, including cologne, perfume, aftershave, and toilet water. Personal fragrance product does not include: (i) deodorant; (ii) medicated products designed primarily to alleviate fungal or bacterial growth on feet or other areas of the body; (iii) mouthwashes, breath fresheners and deodorizers; (iv) lotions, moisturizers, powders or other skin care products used primarily to alleviate skin conditions such as dryness and irritations; (v) products designed exclusively for use on human genitalia; (vi) soaps, shampoos, and products primarily used to clean the human body; and (vii) fragrance products designed to be used exclusively on nonhuman animals.

"Pesticide" means and includes a substance or mixture of substances labeled, designed, or intended for use in preventing, destroying, repelling, or mitigating a pest, or a substance or mixture of substances labeled, designed, or intended for use as a defoliant, desiccant, or plant regulator, provided that the term "pesticide" will not include a substance, mixture of substances, or device that the U.S. Environmental Protection Agency does not consider to be a pesticide.

"Pre-ACP VOC content" means the lowest VOC content of an ACP product between January 1, 1990, and the date on which the application for a proposed ACP is submitted to the board, based on the data obtained from accurate records available to the board that yields the lowest VOC content for the product.

"Pressurized gas duster" means a pressurized product labeled to remove dust from a surface solely by means of mass air or gas flow, including surfaces such as photographs, photographic film negatives, computer keyboards, and other types of surfaces that cannot be cleaned with solvents. Pressurized gas duster does not include dusting aids.

"Principal display panel" means that part of a label that is so designed as to most likely be displayed, presented, shown, or examined under normal and customary conditions of display or purchase. Whenever a principal display panel appears more than once, all requirements pertaining to the principal display panel shall pertain to all such principal display panels.

"Product brand name" means the name of the product exactly as it appears on the principal display panel of the product.

"Product category" means the applicable category that best describes the product as listed in this section and in Table 45-4A in 9VAC5-45-430 A.

"Product form," for the purpose of complying with 9VAC5-45-510 (notification, records and reporting) only, means the applicable form that most accurately describes the product's dispensing form as follows:

"Product line" means a group of products of identical form and function belonging to the same product category.

"Propellant" means a liquefied or compressed gas that is used in whole or in part, such as a cosolvent, to expel a liquid or other material from the same self-pressurized container or from a separate container.

"Pump spray" means a packaging system in which the product ingredients within the container are not under pressure and in which the product is expelled only while a pumping action is applied to a button, trigger, or other actuator.

"Reconcile" or "reconciliation" means to provide sufficient VOC emission reductions to completely offset shortfalls generated under the ACP during an applicable compliance period.

"Reconciliation of shortfalls plan" means the plan to be implemented by the responsible ACP party when shortfalls have occurred, as approved by the board pursuant to 9VAC5-45-440 B 1 g (10).

"Responsible ACP party" means the company, firm, or establishment that is listed on the ACP product's label. If the label lists two or more companies, firms, or establishments, the responsible ACP party is the party that the ACP product was "manufactured for" or "distributed by," as noted on the label.

"Responsible party" means the company, firm, or establishment that is listed on the product's label. If the label lists two companies, firms, or establishments, the responsible party is the party that the product was "manufactured for" or "distributed by," as noted on the label.

"Restricted materials" means pesticides established as restricted materials under Chapter 39 (§ 3.2-3900 et seq.) of Title 3.2 of the Code of Virginia.

"Retail outlet" means an establishment at which consumer products are sold, supplied, or offered for sale directly to consumers.

"Retailer" means a person who sells, supplies, or offers consumer products for sale directly to consumers.

"Roll-on product" means an antiperspirant or deodorant that dispenses active ingredients by rolling a wetted ball or wetted cylinder on the affected area.

"Rubber and vinyl protectant" means a product designed to protect, preserve, or renew vinyl, rubber, and plastic on vehicles, tires, luggage, furniture, and household products such as vinyl covers, clothing, and accessories. Rubber and vinyl protectant does not include products primarily designed to clean the wheel rim, such as aluminum or magnesium wheel cleaners, and tire cleaners that do not leave an appearance-enhancing or protective substance on the tire.

"Rubbing alcohol" means a product containing isopropyl alcohol (also called isopropanol) or denatured ethanol and labeled for topical use, usually to decrease germs in minor cuts and scrapes, to relieve minor muscle aches, as a rubefacient, and for massage.

"Sealant and caulking compound" means a product with adhesive properties that is designed to fill, seal, waterproof, or weatherproof gaps or joints between two surfaces. Sealant and caulking compound does not include roof cements and roof sealants; insulating foams; removable caulking compounds; clear or paintable or water resistant caulking compounds; floor seam sealers; products designed exclusively for automotive uses; or sealers that are applied as continuous coatings. Sealant and caulking compound also does not include units of product, less packaging, which weigh more than one pound and consist of more than 16 fluid ounces. For the purposes of this definition only, "removable caulking compound" means a compound that temporarily seals windows or doors for three- to six-month time intervals; and "clear or paintable or water resistant caulking compound" means a compound that contains no appreciable level of opaque fillers or pigments, transmits most or all visible light through the caulk when cured, is paintable, and is immediately resistant to precipitation upon application.

"Semisolid" means a product that, at room temperature, will not pour, but will spread or deform easily, including, but not limited to gels, pastes, and greases.

"Shaving cream" means an aerosol product that dispenses a foam lather intended to be used with a blade or cartridge razor or other wet-shaving system, in the removal of facial or other bodily hair. Shaving cream does not include shaving gel.

"Shaving gel" means an aerosol product that dispenses a post-foaming semisolid designed to be used with a blade, cartridge razor, or other shaving system in the removal of facial or other bodily hair. Shaving gel does not include shaving cream.

"Shortfall" means the ACP emissions minus the ACP limit when the ACP emissions were greater than the ACP limit during a specified compliance period, expressed to the nearest pound of VOC. Shortfall does not include emissions occurring prior to the date that the ACP agreement approving an ACP is signed by the board.

1. Designed and labeled to provide lubricity primarily through the use of silicone compounds including, but not limited to, polydimethylsiloxane; and

2. Designed and labeled for general purpose lubrication, or for use in a wide variety of applications.

Silicone-based multipurpose lubricant does not include products designed and labeled exclusively to release manufactured products from molds.

"Single phase aerosol air freshener" means an aerosol air freshener with the liquid contents in a single homogeneous phase and that does not require that the product container be shaken before use.

"Small business" means any stationary source that is owned or operated by a person that employs 100 or fewer individuals; is a small business concern as defined in the federal Small Business Act; is not a major stationary source; does not emit 50 tons or more per year of any regulated pollutant; and emits less than 75 tons per year of all regulated pollutants.

"Solid" means a substance or mixture of substances that, either whole or subdivided (such as the particles composing a powder), is not capable of visually detectable flow as determined under ASTM "Standard Test Method for Determining Whether a Material is a Liquid or a Solid" (see 9VAC5-20-21).

"Special purpose spray adhesive" means an aerosol adhesive that meets any of the following definitions:

1. "Mounting adhesive" means an aerosol adhesive designed to permanently mount photographs, artwork, or other drawn or printed media to a backing (paper, board, cloth, etc.) without causing discoloration to the artwork.

2. "Flexible vinyl adhesive" means an aerosol adhesive designed to bond flexible vinyl to substrates. "Flexible vinyl" means a nonrigid polyvinyl chloride plastic with at least 5.0%, by weight, of plasticizer content. A plasticizer is a material, such as a high boiling point organic solvent, that is incorporated into a plastic to increase its flexibility, workability, or distensibility, and may be determined using ASTM "Standard Practice for Packed Column Gas Chromatography" (see 9VAC5-20-21) or from product formulation data.

3. "Polystyrene foam adhesive" means an aerosol adhesive designed to bond polystyrene foam to substrates.

4. "Automobile headliner adhesive" means an aerosol adhesive designed to bond together layers in motor vehicle headliners.

5. "Polyolefin adhesive" means an aerosol adhesive designed to bond polyolefins to substrates.

6. "Laminate repair or edgebanding adhesive" means an aerosol adhesive designed for:

a. The touch-up or repair of items laminated with high pressure laminates (e.g., lifted edges, delaminates, etc.); or

b. The touch-up, repair, or attachment of edgebonding materials, including but not limited to, other laminates, synthetic marble, veneers, wood molding, and decorative metals.

For the purposes of this definition, "high pressure laminate" means sheet materials that consist of paper, fabric, or other core material that have been laminated at temperatures exceeding 265°F and at pressures between 1,000 and 1,400 psi.

7. "Automotive engine compartment adhesive" means an aerosol adhesive designed for use in motor vehicle under-the-hood applications that require oil and plasticizer resistance, as well as high shear strength, at temperatures of 200-275°F.

"Spot remover" means a product labeled to clean localized areas or remove localized spots or stains on cloth or fabric, such as drapes, carpets, upholstery, and clothing, that does not require subsequent laundering to achieve stain removal. Spot remover does not include dry cleaning fluid, laundry prewash, or multipurpose solvent.

"Spray buff product" means a product designed to restore a worn floor finish in conjunction with a floor buffing machine and special pad.

"Stick product" means an antiperspirant or a deodorant that contains active ingredients in a solid matrix form, and that dispenses the active ingredients by frictional action on the affected area.

"Structural waterproof adhesive" means an adhesive whose bond lines are resistant to conditions of continuous immersion in fresh or salt water and that conforms with the definition in the federal consumer products regulation, 40 CFR 59 Subpart C.

"Surplus reduction" means the ACP limit minus the ACP emissions when the ACP limit was greater than the ACP emissions during a given compliance period, expressed to the nearest pound of VOC. Except as provided in 9VAC5-45-440 F 3, surplus reduction does not include emissions occurring prior to the date that the ACP agreement approving an ACP is signed by the board.

"Surplus trading" means the buying, selling, or transfer of surplus reductions between responsible ACP parties.

"Tire sealant and inflator" means a pressurized product that is designed to temporarily inflate and seal a leaking tire.

"Toilet/urinal care product" means any product designed or labeled to clean or to deodorize toilet bowls, toilet tanks, or urinals. Toilet bowls, toilet tanks, or urinals includes, but is not limited to, toilets or urinals connected to permanent plumbing in buildings and other structures, portable toilets or urinals placed at temporary or remote locations, and toilet or urinals in vehicles such as buses, recreational motor homes, boats, ships, and aircraft. Toilet/urinal care product does not include bathroom and tile cleaner or general purpose cleaner.

"Total maximum historical emissions" or "TMHE" means the total VOC emissions from all ACP products for which the responsible ACP party has failed to submit the required VOC content or enforceable sales records. The TMHE shall be calculated for each ACP product during each portion of a compliance period for which the responsible ACP party has failed to provide the required VOC content or enforceable sales records. The TMHE shall be expressed to the nearest pound and calculated according to the following calculation:

Highest VOC content = the maximum VOC content that the ACP product has contained in the previous five years, if the responsible ACP party has failed to meet the requirements for reporting VOC content data (for any portion of the compliance period), as specified in the ACP agreement approving the ACP, or the current actual VOC content, if the responsible ACP party has provided all required VOC Content data (for the entire compliance period), as specified in the ACP agreement.

Highest sales = the maximum one-year gross sales of the ACP product in the previous five years, if the responsible ACP party has failed to meet the requirements for reporting enforceable sales records (for any portion of the compliance period), as specified in the ACP agreement approving the ACP, or the current actual one-year enforceable sales for the product, if the responsible ACP party has provided all required enforceable sales records (for the entire compliance period), as specified in the ACP agreement approving the ACP.

1, 2,..., N = each product in an ACP, up to the maximum N, for which the responsible ACP party has failed to submit the required enforceable sales or VOC content data as specified in the ACP agreement.

"Type A propellant" means a compressed gas such as CO₂, N₂, N₂O, or compressed air that is used as a propellant and is either incorporated with the product or contained in a separate chamber within the product's packaging.

"Type B propellant" means a halocarbon that is used as a propellant including chlorofluorocarbons (CFCs), hydrochlorofluorocarbons (HCFCs), and hydrofluorocarbons (HFCs).

"Type C propellant" means a propellant that is not a Type A or Type B propellant, including propane, isobutane, n-butane, and dimethyl ether (also known as dimethyl oxide).

"Undercoating" means an aerosol product designed to impart a protective, nonpaint layer to the undercarriage, trunk interior, or firewall of motor vehicles to prevent the formation of rust or to deaden sound. Undercoating includes, but is not limited to, rubberized, mastic, or asphaltic products.

"Usage directions" means the text or graphics on the product's principal display panel, label, or accompanying literature that describes to the end user how and in what quantity the product is to be used.

"Vinyl/fabric/leather/polycarbonate coating" means a coating designed and labeled exclusively to coat vinyl, fabric, leather, or polycarbonate substrates.

"VOC content" means, except for charcoal lighter products, the total weight of VOC in a product expressed as a percentage of the product weight (exclusive of the container or packaging), as determined pursuant to 9VAC5-45-490 B and C.

"Volatile organic compound" or "VOC" means volatile organic compound as defined in 9VAC5-10-20.

"Wasp and hornet insecticide" means an insecticide product that is designed for use against wasps, hornets, yellow jackets or bees by allowing the user to spray from a distance a directed stream or burst at the intended insects or their hiding place.

"Waterproofer" means a product designed and labeled exclusively to repel water from fabric or leather substrates. Waterproofer does not include fabric protectants.

"Wax" means a material or synthetic thermoplastic substance generally of high molecular weight hydrocarbons or high molecular weight esters of fatty acids or alcohols, except glycerol and high polymers (plastics). Wax includes, but is not limited to, substances derived from the secretions of plants and animals such as carnauba wax and beeswax, substances of a mineral origin such as ozocerite and paraffin, and synthetic polymers such as polyethylene.

"Web spray adhesive" means an aerosol adhesive that is not a mist spray or special purpose spray adhesive.

"Wood cleaner" means a product labeled to clean wooden materials including but not limited to decking, fences, flooring, logs, cabinetry, and furniture. Wood cleaner does not include dusting aids, general purpose cleaners, furniture maintenance products, floor wax strippers, floor polish or waxes, or products designed and labeled exclusively to preserve or color wood.

"Working day" means a day between Monday through Friday, inclusive, except for federal holidays.

A. Except as provided in 9VAC5-45-410, 9VAC5-45-440, and 9VAC5-45-450, no owner or other person shall (i) sell, supply, or offer for sale a consumer product manufactured on or after [ ~~May 1, 2010~~ ] August 1, 2010, or (ii) manufacture for sale a consumer product on or after [ ~~May 1, 2010~~ ] August 1, 2010, that contains volatile organic compounds in excess of the limits specified in Table 45-4A.

1. For consumer products for which the label, packaging, or accompanying literature specifically states that the product should be diluted with water or non-VOC solvent prior to use, the limits specified in Table 45-4A shall apply to the product only after the minimum recommended dilution has taken place. For purposes of this subsection, "minimum recommended dilution" shall not include recommendations for incidental use of a concentrated product to deal with limited special applications such as hard-to-remove soils or stains.

2. For consumer products for which the label, packaging, or accompanying literature states that the product should be diluted with a VOC solvent prior to use, the limits specified in Table 45-4A shall apply to the product only after the maximum recommended dilution has taken place.

D. For those consumer products that are registered under FIFRA, the effective date of the VOC standards in Table 45-4A shall be [ ~~May 1, 2010~~ ] August 1, 2011. Prior to that date, the standards of Table 45-3A in 9VAC5-45-430 A shall apply unless the product is exempt under the provisions of 9VAC5-45-410.

E. The following requirements shall apply to all charcoal lighter material products:

1. Effective as of the applicable compliance date specified in 9VAC5-45-480, no owner or other person shall (i) sell, supply, or offer for sale a charcoal lighter material product manufactured on or after [ ~~May 1, 2010~~ ] August 1, 2010, or (ii) manufacture for sale a charcoal lighter material product on or after [ ~~May 1, 2010~~ ] August 1, 2010, unless at the time of the transaction:

b. The manufacturer or distributor of the charcoal lighter material has been issued a currently effective certification pursuant to subdivision 2 of this subsection.

c. The charcoal lighter material meets the formulation criteria and other conditions specified in the applicable ACP agreement issued pursuant to subdivision 2 of this subsection.

d. The product usage directions for the charcoal lighter material are the same as those provided to the board pursuant to subdivision 2 c of this subsection.

a. No charcoal lighter material formulation shall be certified under this subdivision unless the applicant for certification demonstrates to the board's satisfaction that the VOC emissions from the ignition of charcoal with the charcoal lighter material are less than or equal to 0.020 pound of VOC per start, using the procedures specified in the South Coast Air Quality Management District Rule 1174 Ignition Method Compliance Certification Protocol (see 9VAC5-20-21). The provisions relating to LVP-VOC in 9VAC5-45-410 F and 9VAC5-45-420 C shall not apply to a charcoal lighter material subject to the requirements of 9VAC5-45-430 A and this subsection.

(1) The results of testing conducted pursuant to the procedures specified in South Coast Air Quality Management District Rule 1174 Testing Protocol (see 9VAC5-20-21); and

(a) The charcoal lighter material is intended to be used in fixed amounts independent of the amount of charcoal used, such as certain paraffin cubes, or

(b) The charcoal lighter material is already incorporated into the charcoal, such as certain "bag light," "instant light" or "match light" products.

1. The standards for aerosol adhesives apply to all uses of aerosol adhesives, including consumer, industrial, and commercial uses. Except as otherwise provided in 9VAC5-45-410 and 9VAC5-45-450, no owner or other person shall (i) sell, supply, offer for sale, or use an aerosol adhesive manufactured on or after [ ~~May 1, 2010~~ ] August 1, 2010, or (ii) manufacture for sale an aerosol adhesive [ ~~after May 1, 2010~~ on or after ] August 1, 2010, that contains VOCs in excess of the specified standard.

2. a. In order to qualify as a "special purpose spray adhesive," the product must meet one or more of the definitions for special purpose spray adhesive specified in 9VAC5-45-420 C, but if the product label indicates that the product is suitable for use on a substrate or application not listed in 9VAC5-45-420 C, then the product shall be classified as either a "web spray adhesive" or a "mist spray adhesive."

b. If a product meets more than one of the definitions specified in 9VAC5-45-420 C for "special purpose spray adhesive," and is not classified as a "web spray adhesive" or "mist spray adhesive" under subdivision 2 a of this subsection, then the VOC limit for the product shall be the lowest applicable VOC limit specified in 9VAC5-45-430 A.

3. No person shall (i) sell, supply, or offer for sale an aerosol adhesive manufactured on or after [ ~~May 1, 2010~~ ] August 1, 2010, or (ii) manufacture for sale on or after [ ~~May 1, 2010~~ ] August 1, 2010, an aerosol adhesive, that contains any of the following compounds: methylene chloride, perchloroethylene, or trichloroethylene.

4. All aerosol adhesives must comply with the labeling requirements specified in 9VAC5-45-460 D.

G. Effective as of the applicable compliance date specified in 9VAC5-45-480, no owner or other person shall sell, supply, offer for sale, or manufacture for use a floor wax stripper unless the following requirements are met:

1. The label of each nonaerosol floor wax stripper must specify a dilution ratio for light or medium build-up of polish that results in an as-used VOC concentration of 3.0% by weight or less.

3. The terms "light build-up," "medium build-up," or "heavy build-up" are not specifically required as long as comparable terminology is used.

H. For a consumer product for which standards are specified under subsection A of this section, no owner or other person shall sell, supply, offer for sale, or manufacture for sale a consumer product that contains any of the following ozone-depleting compounds:

HCFC-141b (1,1-dichloro-1-fluoroethane), HCFC-142b (1-chloro-1,1-difluoroethane);

I. The requirements of subsection H of this section shall not apply to an existing product formulation that complies with Table 45-4A or an existing product formulation that is reformulated to meet Table 45-4A, provided the ozone-depleting compound content of the reformulated product does not increase.

J. The requirements of subsection H of this section shall not apply to ozone-depleting compounds that may be present as impurities in a consumer product in an amount equal to or less than 0.01% by weight of the product.