Section 420. Definitions

A. For the purpose of applying this article in the context of the Regulations for the Control and Abatement of Air Pollution and related uses, the words or terms shall have the meanings given them in subsection C of this section.

B. As used in this article, all terms not defined herein shall have the meanings given them in 9VAC5-10 (General Definitions), unless otherwise required by context.

C. Terms defined.

"ACP" or "alternative control plan" means any emissions averaging program approved by the board pursuant to the provisions of this article.

"ACP agreement" means the document signed by the board that includes the conditions and requirements of the board and that allows manufacturers to sell ACP products pursuant to the requirements of this article.

"ACP emissions" means the sum of the VOC emissions from every ACP product subject to an ACP agreement approving an ACP, during the compliance period specified in the ACP agreement, expressed to the nearest pound of VOC and calculated according to the following equation:

where:

1, 2,...N = each product in an ACP up to the maximum N.

Enforceable sales = (see definition in this section).

VOC content = one of the following:

1. For all products except for charcoal lighter material products:

where:

A = total net weight of unit (excluding container and packaging).

B = total weight of all VOCs per unit.

C = total weight of all exempted VOCs per unit, as specified in 9VAC5-45-410.

2. For charcoal lighter material products only:

where:

Certified emissions = (see definition in this section).

Certified use rate = (see definition in this section).

"ACP limit" means the maximum allowable ACP emissions during the compliance period specified in an ACP agreement approving an ACP, expressed to the nearest pound of VOC, and calculated according to the following equation:

where:

where:

Enforceable sales = (see definition in this section).

ACP standard = (see definition in this section).

1, 2,...N = each product in an ACP up to the maximum N.

"ACP product" means any consumer product subject to the VOC standards specified in 9VAC5-45-430 A, except those products that have been exempted as innovative products under 9VAC5-45-450.

"ACP reformulation" or "ACP reformulated" means the process of reducing the VOC content of an ACP product within the period that an ACP is in effect to a level that is less than the current VOC content of the product.

"ACP standard" means either the ACP product's pre-ACP VOC content or the applicable VOC standard specified in 9VAC5-45-430 A, whichever is the lesser of the two.

"ACP VOC standard" means the maximum allowable VOC content for an ACP product, determined as follows:

1. The applicable VOC standard specified in 9VAC5-45-430 A for all ACP products except for charcoal lighter material;

2. For charcoal lighter material products only, the VOC standard for the purposes of this article shall be calculated according to the following equation:

where:

0.020 = the certification emissions level for the product, as specified in 9VAC5-45-430 E.

Certified use rate = (see definition in this section).

"Adhesive" means any product that is used to bond one surface to another by attachment. Adhesive does not include products used on humans and animals, adhesive tape, contact paper, wallpaper, shelf liners, or any other product with an adhesive incorporated onto or in an inert substrate. For contact adhesive only, adhesive also does not include units of product, less packaging, that consist of more than one gallon. In addition, for construction, panel, and floor covering adhesive and general purpose adhesive only, adhesive does not include units of product, less packaging, that weigh more than one pound and consist of more than 16 fluid ounces. The package size limitations do not apply to aerosol adhesives.

"Adhesive remover" means a product designed to remove adhesive from either a specific substrate or a variety of substrates. Adhesive remover does not include products that remove adhesives intended exclusively for use on humans or animals. For the purpose of this definition and the following adhesive remover subcategories in subdivisions 1 through 4 of this definition, adhesive shall mean a substance used to bond one or more materials. Adhesives include, but are not limited to, caulk, sealant, glue, or similar substances used for the purpose of forming a bond.

1. "Floor and wall covering adhesive remover" means a product designed or labeled to remove floor or wall coverings and associated adhesive from the underlying substrate.

2. "Gasket or thread locking adhesive remover" means a product designed or labeled to remove gaskets or thread locking adhesives. Products labeled for dual use as a paint stripper and as a gasket remover or thread locking adhesive remover are considered gasket or thread locking adhesive remover.

3. "General purpose adhesive remover" means a product designed or labeled to remove cyanoacrylate adhesives and nonreactive adhesives or residue from a variety of substrates. General purpose adhesive remover includes, but is not limited to, products that remove thermoplastic adhesives, pressure sensitive adhesives, dextrin-based or starch-based adhesives, casein glues, rubber-based or latex-based adhesives, as well as products that remove stickers, decals, stencils, or similar materials. General purpose adhesive remover does not include floor or wall covering adhesive remover.

4. "Specialty adhesive remover" means a product designed to remove reactive adhesives from a variety of substrates. Reactive adhesives include adhesives that require a hardener or catalyst in order for the bond to occur. Examples of reactive adhesives include, but are not limited to, epoxies, urethanes, and silicones. Specialty adhesive remover does not include gasket or thread locking adhesive remover.

"Aerosol adhesive" means an aerosol product in which the spray mechanism is permanently housed in a nonrefillable can designed for hand-held application without the need for ancillary hoses or spray equipment. Aerosol adhesives include special purpose spray adhesives, mist spray adhesives, and web spray adhesives.

"Aerosol cooking spray" means any aerosol product designed either to reduce sticking on cooking and baking surfaces or to be applied on food, or both.

"Aerosol product" means a pressurized spray system that dispenses product ingredients by means of a propellant contained in a product or a product's carrier, or by means of a mechanically induced force. Aerosol product does not include pump sprays.

"Agricultural use" means the use of any pesticide or method or device for the control of pests in connection with the commercial production, storage, or processing of any animal or plant crop. Agricultural use does not include the sale or use of pesticides in properly labeled packages or containers that are intended for home use, use in structural pest control, industrial use, or institutional use. For the purposes of this definition only:

1. "Home use" means use in a household or its immediate environment.

2. "Industrial use" means use for or in a manufacturing, mining, or chemical process or use in the operation of factories, processing plants, and similar sites.

3. "Institutional use" means use within the perimeter of, or on property necessary for the operation of, buildings such as hospitals, schools, libraries, auditoriums, and office complexes.

4. "Structural pest control" means a use requiring a license under the applicable state pesticide licensing requirement.

"Air freshener" means any consumer product including, but not limited to, sprays, wicks, powders, and crystals, designed for the purpose of masking odors or freshening, cleaning, scenting, or deodorizing the air. Air fresheners do not include products that are used on the human body, products that function primarily as cleaning products (as indicated on a product label) or as toilet/urinal care products, disinfectant products claiming to deodorize by killing germs on surfaces, or institutional or industrial disinfectants when offered for sale solely through institutional and industrial channels of distribution. Air fresheners do include spray disinfectants and other products that are expressly represented for use as air fresheners, except institutional and industrial disinfectants when offered for sale through institutional and industrial channels of distribution. To determine whether a product is an air freshener, all verbal and visual representations regarding product use on the label or packaging and in the product's literature and advertising may be considered. The presence of, and representations about, a product's fragrance and ability to deodorize (resulting from surface application) shall not constitute a claim of air freshening.

"All other carbon-containing compounds" means all other compounds that contain at least one carbon atom and are not an "exempt compound" or an "LVP-VOC."

"All other forms" means all consumer product forms for which no form-specific VOC standard is specified. Unless specified otherwise by the applicable VOC standard, all other forms include, but are not limited to, solids, liquids, wicks, powders, crystals, and cloth or paper wipes (towelettes).

"Alternative control plan" or "ACP" means any emissions averaging program approved by the board pursuant to the provisions of this article.

"Antimicrobial hand or body cleaner or soap" means a cleaner or soap that is designed to reduce the level of microorganisms on the skin through germicidal activity. Antimicrobial hand or body cleaner or soap includes, but is not limited to, antimicrobial hand or body washes or cleaners, food handler hand washes, health care personnel hand washes, pre-operative skin preparations, and surgical scrubs. Antimicrobial hand or body cleaner or soap does not include prescription drug products, antiperspirants, astringent or toner, deodorant, facial cleaner or soap, general-use hand or body cleaner or soap, hand dishwashing detergent (including antimicrobial), heavy-duty hand cleaner or soap, medicated astringent or medicated toner, and rubbing alcohol.

"Antiperspirant" means any product including, but not limited to, aerosols, roll-ons, sticks, pumps, pads, creams, and squeeze-bottles, that is intended by the manufacturer to be used to reduce perspiration in the human axilla by at least 20% in at least 50% of a target population.

"Anti-static product" means a product that is labeled to eliminate, prevent, or inhibit the accumulation of static electricity. Anti-static products do not include electronic cleaners, floor polish or waxes, floor coatings, and products that meet the definition of aerosol coating products or architectural coatings.

"Architectural coating" means a coating applied to stationary structures and their appurtenances, to mobile homes, to pavements, or to curbs.

"ASTM" means the American Society for Testing and Materials.

"Astringent or toner" means any product not regulated as a drug by the United States Food and Drug Administration that is applied to the skin for the purpose of cleaning or tightening pores. This category also includes clarifiers and substrate-impregnated products. This category does not include any hand, face, or body cleaner or soap product, medicated astringent or medicated toner, cold cream, lotion, or antiperspirant.

"Automotive brake cleaner" means a cleaning product designed to remove oil, grease, brake fluid, brake pad material, or dirt from motor vehicle brake mechanisms.

"Automotive hard paste wax" means an automotive wax or polish that is:

1. Designed to protect and improve the appearance of automotive paint surfaces;

2. A solid at room temperature; and

3. Contains no water.

"Automotive instant detailer" means a product designed for use in a pump spray that is applied to the painted surface of automobiles and wiped off prior to the product being allowed to dry.

"Automotive rubbing or polishing compound" means a product designed primarily to remove oxidation, old paint, scratches or swirl marks, and other defects from the painted surfaces of motor vehicles without leaving a protective barrier.

"Automotive wax, polish, sealant, or glaze" means a product designed to seal out moisture, increase gloss, or otherwise enhance a motor vehicle's painted surfaces. Automotive wax, polish, sealant, or glaze includes, but is not limited to, products designed for use in auto body repair shops and drive-through car washes, as well as products designed for the general public. Automotive wax, polish, sealant, or glaze does not include automotive rubbing or polishing compounds, automotive wash and wax products, surfactant-containing car wash products, and products designed for use on unpainted surfaces such as bare metal, chrome, glass, or plastic.

"Automotive windshield washer fluid" means any liquid designed for use in a motor vehicle windshield washer system either as an antifreeze or for the purpose of cleaning, washing, or wetting the windshield. Automotive windshield washer fluid also includes liquids that are (i) packaged as a pre-wetted, single-use manual wipe and (ii) designed exclusively for cleaning, washing, or wetting automotive glass surfaces for the purpose of restoring or maintaining visibility for the driver. Glass cleaners that are intended for use on other glass surfaces are not included in this definition. Automotive windshield washer fluid does not include fluids placed by the manufacturer in a new vehicle.

"Bathroom and tile cleaner" means a product designed to clean tile or surfaces in bathrooms. Bathroom and tile cleaners do not include products designed primarily to clean toilet bowls, toilet tanks, or urinals.

"Bug and tar remover" means a product labeled to remove either or both of the following from painted motor vehicle surfaces without causing damage to the finish: (i) biological residues, such as insect carcasses and tree sap, and (ii) road grime, such as road tar, roadway paint markings, and asphalt.

"CARB" means the California Air Resources Board.

"Carburetor or fuel-injection air intake cleaner" means a product designed to remove fuel deposits, dirt, or other contaminants from a carburetor, choke, throttle body of a fuel-injection system, or associated linkages. Carburetor or fuel-injection air intake cleaner does not include products designed exclusively to be introduced directly into the fuel lines or fuel storage tank prior to introduction into the carburetor or fuel injectors.

"Carpet and upholstery cleaner" means a cleaning product designed for the purpose of eliminating dirt and stains on rugs, carpeting, and the interior of motor vehicles or on household furniture or objects upholstered or covered with fabrics such as wool, cotton, nylon, or other synthetic fabrics. Carpet and upholstery cleaners include, but are not limited to, products that make fabric protectant claims. Carpet and upholstery cleaners do not include general purpose cleaners, spot removers, vinyl or leather cleaners, dry cleaning fluids, or products designed exclusively for use at industrial facilities engaged in furniture or carpet manufacturing.

"Certified emissions" means the emissions level for products approved under 9VAC5-45-430 E, as determined pursuant to South Coast Air Quality Management District Rule 1174 Ignition Method Compliance Certification Protocol (see 9VAC5-20-21), expressed to the nearest 0.001 pound VOC per start.

"Certified use rate" means the usage level for products approved under 9VAC5-45-430 E, as determined pursuant to South Coast Air Quality Management District Rule 1174 Ignition Method Compliance Certification Protocol (see 9VAC5-20-21), expressed to the nearest 0.001 pound certified product used per start.

"Charcoal lighter material" means any combustible material designed to be applied on, incorporated in, added to, or used with charcoal to enhance ignition. Charcoal lighter material does not include any of the following:

1. Electrical starters and probes;

2. Metallic cylinders using paper tinder;

3. Natural gas;

4. Propane; or

5. Fat wood.

"Colorant" means any pigment or coloring material used in a consumer product for an aesthetic effect or to dramatize an ingredient.

"Compliance period" means the period of time, not to exceed one year, for which the ACP limit and ACP emissions are calculated and for which compliance with the ACP limit is determined, as specified in the ACP agreement approving an ACP.

"Construction, panel, and floor covering adhesive" means any one-component adhesive that is designed exclusively for the installation, remodeling, maintenance, or repair of:

1. Structural and building components that include, but are not limited to, beams, trusses, studs, paneling (drywall or drywall laminates, fiberglass reinforced plastic (FRP), plywood, particle board, insulation board, predecorated hardboard or tileboard, etc.), ceiling and acoustical tile, molding, fixtures, countertops or countertop laminates, cove or wall bases, and flooring or subflooring; or

2. Floor or wall coverings that include, but are not limited to, wood or simulated wood covering, carpet, carpet pad or cushion, vinyl-backed carpet, flexible flooring material, nonresilient flooring material, mirror tiles and other types of tiles, and artificial grass.

Construction, panel, and floor covering adhesive does not include floor seam sealer.

"Consumer" means a person who purchases or acquires a consumer product for personal, family, household, or institutional use. Persons acquiring a consumer product for resale are not consumers for that product.

"Consumer product" means a chemically formulated product used by household and institutional consumers including, but not limited to, detergents; cleaning compounds; polishes; floor finishes; cosmetics; personal care products; home, lawn, and garden products; disinfectants; sanitizers; aerosol paints; and automotive specialty products, but does not include other paint products, furniture coatings, or architectural coatings. As used in this article, consumer products shall also refer to aerosol adhesives, including aerosol adhesives used for consumer, industrial, or commercial uses.

"Contact adhesive" means an adhesive that:

1. Is designed for application to both surfaces to be bonded together;

2. Is allowed to dry before the two surfaces are placed in contact with each other;

3. Forms an immediate bond that is impossible, or difficult, to reposition after both adhesive-coated surfaces are placed in contact with each other; and

4. Does not need sustained pressure or clamping of surfaces after the adhesive-coated surfaces have been brought together using sufficient momentary pressure to establish full contact between both surfaces.

Contact adhesive does not include rubber cements that are primarily intended for use on paper substrates. Contact adhesive also does not include vulcanizing fluids that are designed and labeled for tire repair only.

"Contact adhesive - general purpose" means any contact adhesive that is not a contact adhesive - special purpose.

"Contact adhesive - special purpose" means a contact adhesive that is used as follows:

1. To bond melamine-covered board, unprimed metal, unsupported vinyl, Teflon®, ultra-high molecular weight polyethylene, rubber, high pressure laminate or wood veneer 1/16 inch or less in thickness to any porous or nonporous surface, and is sold in units of product, less packaging, that contain more than eight fluid ounces; or

2. In automotive applications that are either:

a. Automotive under-the-hood applications requiring heat, oil, or gasoline resistance; or

b. Body-side molding, automotive weatherstrip, or decorative trim.

"Container or packaging" means the part or parts of the consumer or institutional product that serve only to contain, enclose, incorporate, deliver, dispense, wrap, or store the chemically formulated substance or mixture of substances that is solely responsible for accomplishing the purposes for which the product was designed or intended. Containers or packaging include any article onto or into which the principal display panel and other accompanying literature or graphics are incorporated, etched, printed, or attached.

"Contact person" means a representative that has been designated by the responsible ACP party for the purpose of reporting or maintaining information specified in the ACP agreement approving an ACP.

"Crawling bug insecticide" means an insecticide product that is designed for use against ants, cockroaches, or other household crawling arthropods, including, but not limited to, mites, silverfish or spiders. Crawling bug insecticide does not include products designed to be used exclusively on humans or animals or a house dust mite product. For the purposes of this definition only:

1. "House dust mite product" means a product whose label, packaging, or accompanying literature states that the product is suitable for use against house dust mites, but does not indicate that the product is suitable for use against ants, cockroaches, or other household crawling arthropods.

2. "House dust mite" means mites that feed primarily on skin cells shed in the home by humans and pets and that belong to the phylum Arthropoda, the subphylum Chelicerata, the class Arachnida, the subclass Acari, the order Astigmata, and the family Pyroglyphidae.

"Date-code" means the day, month, and year on which the consumer product was manufactured, filled, or packaged, or a code indicating such a date.

"Deodorant" means any product including, but not limited to, aerosols, roll-ons, sticks, pumps, pads, creams, and squeeze-bottles, that indicates or depicts on the container or packaging, or on any sticker or label affixed thereto, that the product can be used on or applied to the human axilla to provide a scent or minimize odor. A deodorant body spray product that indicates or depicts on the container or packaging, or on any sticker or label affixed thereto, that it can be used on or applied to the human axilla, is a deodorant.

"Deodorant body spray" means a personal fragrance product with 20% or less fragrance that is designed for application all over the human body to provide a scent. A deodorant body spray product that indicates or depicts on the container or packaging, or on any sticker or label affixed thereto, that it can be used on or applied to the human axilla, is a deodorant.

"Device" means an instrument or contrivance (other than a firearm) that is designed for trapping, destroying, repelling, or mitigating a pest or other form of plant or animal life (other than human and other than bacterium, virus, or another microorganism on or in living humans or other living animals); but not including equipment used for the application of pesticides when sold separately therefrom.

"Disinfectant" means a product intended to destroy or irreversibly inactivate infectious or other undesirable bacteria, pathogenic fungi, or viruses on surfaces or inanimate objects and whose label is registered under the FIFRA. Disinfectant does not include any of the following:

1. Products designed solely for use on humans or animals;

2. Products designed for agricultural use;

3. Products designed solely for use in swimming pools, therapeutic tubs, or hot tubs; or

4. Products that, as indicated on the principal display panel or label, are designed primarily for use as bathroom and tile cleaners, glass cleaners, general purpose cleaners, toilet bowl cleaners, or metal polishes.

"Distributor" means a person to whom a consumer product is sold or supplied for the purposes of resale or distribution in commerce, except that manufacturers, retailers, and consumers are not distributors.

"Double phase aerosol air freshener" means an aerosol air freshener with the liquid contents in two or more distinct phases that require the product container to be shaken before use to mix the phases, producing an emulsion.

"Dry cleaning fluid" means a nonaqueous liquid product designed and labeled exclusively for use on:

1. Fabrics that are labeled "for dry clean only," such as clothing or drapery; or

2. S-coded fabrics.

Dry cleaning fluid includes, but is not limited to, those products used by commercial dry cleaners and commercial businesses that clean fabrics such as draperies at the customer's residence or work place. Dry cleaning fluid does not include spot remover or carpet and upholstery cleaner. For the purposes of this definition, "S-coded fabric" means an upholstery fabric designed to be cleaned only with water-free spot cleaning products as specified by the American Furniture Manufacturers Association Joint Industry Fabrics Standards Committee, Woven and Knit Residential Upholstery Fabric Standards and Guidelines (see 9VAC5-20-21).

"Dusting aid" means a product designed to assist in removing dust and other soils from floors and other surfaces without leaving a wax or silicone-based coating. Dusting aid does not include pressurized gas dusters.

"Electrical cleaner" means a product labeled to remove heavy soils such as grease, grime, or oil from electrical equipment, including, but not limited to, electric motors, armatures, relays, electric panels, or generators. Electrical cleaner does not include general purpose cleaners, general purpose degreasers, dusting aids, electronic cleaners, energized electrical cleaners, pressurized gas dusters, engine degreasers, anti-static products, or products designed to clean the casings or housings of electrical equipment.

"Electronic cleaner" means a product labeled for the removal of dirt, moisture, dust, flux or oxides from the internal components of electronic or precision equipment such as circuit boards, and the internal components of electronic devices, including but not limited to, radios, compact disc (CD) players, digital video disc (DVD) players, and computers. Electronic cleaner does not include general purpose cleaners, general purpose degreasers, dusting aids, pressurized gas dusters, engine degreasers, electrical cleaners, energized electrical cleaners, anti-static products, or products designed to clean the casings or housings of electronic equipment.

"Energized electrical cleaner" means a product that meets both of the following criteria:

1. The product is labeled to clean or degrease electrical equipment, where cleaning or degreasing is accomplished when electrical current exists, or when there is a residual electrical potential from a component, such as a capacitor;

2. The product label clearly displays the statements: "Energized equipment use only. Not to be used for motorized vehicle maintenance, or their parts."

Energized electrical cleaner does not include electronic cleaner.

"Enforceable sales" means the total amount of an ACP product sold for use in the applicable volatile organic compound emissions control areas designated in 9VAC5-45-400 C during the applicable compliance period specified in the ACP agreement approving an ACP, as determined through enforceable sales records (expressed to the nearest pound, excluding product container and packaging).

"Enforceable sales record" means a written, point-of-sale record or another board-approved system of documentation from which the mass, in pounds (less product container and packaging), of an ACP product sold to the end user in the applicable volatile organic compound emissions control areas designated in 9VAC5-45-400 C during the applicable compliance period can be accurately documented. For the purposes of this article, enforceable sales records include, but are not limited to, the following types of records:

1. Accurate records of direct retail or other outlet sales to the end user during the applicable compliance period;

2. Accurate compilations, made by independent market surveying services, of direct retail or other outlet sales to the end users for the applicable compliance period, provided that a detailed method that can be used to verify data composing such summaries is submitted by the responsible ACP party and approved by the board; and

3. Other accurate product sales records acceptable to the board.

"Engine degreaser" means a cleaning product designed to remove grease, grime, oil, and other contaminants from the external surfaces of engines and other mechanical parts.

"Exempt compound" means acetone, ethane, methyl acetate, parachlorobenzotrifluoride (1-chloro-4-trifluoromethyl benzene), or perchloroethylene (tetrachloroethylene).

"Existing product" means any formulation of the same product category and form sold, supplied, manufactured, or offered for sale prior to March 9, 2005, or any subsequently introduced identical formulation.

"Fabric protectant" means a product designed to be applied to fabric substrates to protect the surface from soiling from dirt and other impurities or to reduce absorption of liquid into the fabric's fibers. Fabric protectant does not include waterproofers, products designed for use solely on leather, or products designed for use solely on fabrics that are labeled "for dry clean only" and sold in containers of 10 fluid ounces or less.

"Fabric refresher" means a product labeled to neutralize or eliminate odors on non-laundered fabric including, but not limited to, soft household surfaces, rugs, carpeting, draperies, bedding, automotive interiors, footwear, athletic equipment, clothing or on household furniture or objects upholstered or covered with fabrics such as, but not limited to, wool, cotton, or nylon. Fabric refresher does not include anti-static products, carpet and upholstery cleaners, soft household surface sanitizers, footwear or leather care products, spot removers, or disinfectants, or products labeled for application to both fabric and human skin. For the purposes of this definition only, soft household surface sanitizer means a product labeled to neutralize or eliminate odors on surfaces listed above whose label is registered as a sanitizer under FIFRA.

"Facial cleaner or soap" means a cleaner or soap designed primarily to clean the face. Facial cleaner or soap includes, but is not limited to, facial cleansing creams, semisolids, liquids, lotions, and substrate-impregnated forms. Facial cleaner or soap does not include prescription drug products, antimicrobial hand or body cleaner or soap, astringent or toner, general-use hand or body cleaner or soap, medicated astringent or medicated toner, or rubbing alcohol.

"Fat wood" means pieces of wood kindling with high naturally occurring levels of sap or resin that enhance ignition of the kindling. Fat wood does not include kindling with substances added to enhance flammability, such as wax-covered or wax-impregnated wood-based products.

"FIFRA" means the Federal Insecticide, Fungicide, and Rodenticide Act (7 USC § 136-136y).

"Flea and tick insecticide" means an insecticide product that is designed for use against fleas, ticks, their larvae, or their eggs. Flea and tick insecticide does not include products that are designed to be used exclusively on humans or animals and their bedding.

"Flexible flooring material" means asphalt, cork, linoleum, no-wax, rubber, seamless vinyl, and vinyl composite flooring.

"Floor coating" means an opaque coating that is labeled and designed for application to flooring, including but not limited to, decks, porches, steps, and other horizontal surfaces that may be subject to foot traffic.

"Floor polish or wax" means a wax, polish, or other product designed to polish, protect, or enhance floor surfaces by leaving a protective coating that is designed to be periodically replenished. Floor polish or wax does not include spray buff products, products designed solely for the purpose of cleaning floors, floor finish strippers, products designed for unfinished wood floors, and coatings subject to architectural coatings regulations.

"Floor seam sealer" means a product designed and labeled exclusively for bonding, fusing, or sealing (coating) seams between adjoining rolls of installed flexible sheet flooring.

"Floor wax stripper" means a product designed to remove natural or synthetic floor polishes or waxes through breakdown of the polish or wax polymers or by dissolving or emulsifying the polish or wax. Floor wax stripper does not include aerosol floor wax strippers or products designed to remove floor wax solely through abrasion.

"Flying bug insecticide" means an insecticide product that is designed for use against flying insects or other flying arthropods, including but not limited to flies, mosquitoes, moths, or gnats. Flying bug insecticide does not include wasp and hornet insecticide, products that are designed to be used exclusively on humans or animals, or a moth-proofing product. For the purposes of this definition only, "moth-proofing product" means a product whose label, packaging, or accompanying literature indicates that the product is designed to protect fabrics from damage by moths, but does not indicate that the product is suitable for use against flying insects or other flying arthropods.

"Footwear or leather care product" means any product designed or labeled to be applied to footwear or to other leather articles or components, to maintain, enhance, clean, protect, or modify the appearance, durability, fit, or flexibility of the footwear, leather article or component. Footwear includes both leather and non-leather foot apparel. Footwear or leather care product does not include fabric protectants; general purpose adhesives; contact adhesives; vinyl/fabric/leather/polycarbonate coatings; rubber and vinyl protectants; fabric refreshers; products solely for deodorizing; or sealant products with adhesive properties used to create external protective layers greater than 2 millimeters thick.

"Fragrance" means a substance or complex mixture of aroma chemicals, natural essential oils, and other functional components with a combined vapor pressure not in excess of 2 mm of Hg at 20ºC, the sole purpose of which is to impart an odor or scent, or to counteract a malodor.

"Furniture coating" means a paint designed for application to room furnishings including, but not limited to, cabinets (kitchen, bath and vanity), tables, chairs, beds, and sofas.

"Furniture maintenance product" means a wax, polish, conditioner, or other product designed for the purpose of polishing, protecting, or enhancing finished wood surfaces other than floors. Furniture maintenance products do not include dusting aids, wood cleaners and products designed solely for the purpose of cleaning, and products designed to leave a permanent finish such as stains, sanding sealers, and lacquers.

"Gel" means a colloid in which the disperse phase has combined with the continuous phase to produce a semisolid material, such as jelly.

"General purpose adhesive" means a nonaerosol adhesive designed for use on a variety of substrates. General purpose adhesive does not include:

1. Contact adhesives;

2. Construction, panel, and floor covering adhesives;

3. Adhesives designed exclusively for application on one specific category of substrates (i.e., substrates that are composed of similar materials, such as different types of metals, paper products, ceramics, plastics, rubbers, or vinyls); or

4. Adhesives designed exclusively for use on one specific category of articles (i.e., articles that may be composed of different materials but perform a specific function, such as gaskets, automotive trim, weather-stripping, or carpets).

"General purpose cleaner" means a product designed for general all-purpose cleaning, in contrast to cleaning products designed to clean specific substrates in certain situations. General purpose cleaner includes products designed for general floor cleaning, kitchen or countertop cleaning, and cleaners designed to be used on a variety of hard surfaces and does not include general purpose degreasers and electronic cleaners.

"General purpose degreaser" means a product labeled to remove or dissolve grease, grime, oil, and other oil-based contaminants from a variety of substrates, including automotive or miscellaneous metallic parts. General purpose degreaser does not include engine degreaser, general purpose cleaner, adhesive remover, electronic cleaner, electrical cleaner, energized electrical cleaner, metal polish or cleanser, products used exclusively in solvent cleaning tanks or related equipment, or products that are (i) sold exclusively to establishments that manufacture or construct goods or commodities; and (ii) labeled "not for retail sale." Solvent cleaning tanks or related equipment includes, but is not limited to, cold cleaners, vapor degreasers, conveyorized degreasers, film cleaning machines, or products designed to clean miscellaneous metallic parts by immersion in a container.

"General-use hand or body cleaner or soap" means a cleaner or soap designed to be used routinely on the skin to clean or remove typical or common dirt and soils. General-use hand or body cleaner or soap includes, but is not limited to, hand or body washes, dual-purpose shampoo-body cleaners, shower or bath gels, and moisturizing cleaners or soaps. General-use hand or body cleaner or soap does not include prescription drug products, antimicrobial hand or body cleaner or soap, astringent or toner, facial cleaner or soap, hand dishwashing detergent (including antimicrobial), heavy-duty hand cleaner or soap, medicated astringent or medicated toner, or rubbing alcohol.

"Glass cleaner" means a cleaning product designed primarily for cleaning surfaces made of glass. Glass cleaner does not include products designed solely for the purpose of cleaning optical materials used in eyeglasses, photographic equipment, scientific equipment, and photocopying machines.

"Graffiti remover" means a product labeled to remove spray paint, ink, marker, crayon, lipstick, nail polish, or shoe polish, from a variety of non-cloth or non-fabric substrates. Graffiti remover does not include paint remover or stripper, nail polish remover, or spot remover. Products labeled for dual use as both a paint stripper and graffiti remover are considered graffiti removers.

"Gross sales" means the estimated total sales of an ACP product in the applicable volatile organic compound emissions control areas designated in 9VAC5-45-400 C during a specific compliance period (expressed to the nearest pound), based on either of the following methods, whichever the responsible ACP party demonstrates to the satisfaction of the board will provide an accurate sales estimate:

1. Apportionment of national or regional sales of the ACP product to sales, determined by multiplying the average national or regional sales of the product by the fraction of the national or regional population, respectively, that is represented by the current population of the applicable volatile organic compound emissions control areas designated in 9VAC5-45-400 C; or

2. Another documented method that provides an accurate estimate of the total current sales of the ACP product.

"Hair mousse" means a hairstyling foam designed to facilitate styling of a coiffure and provide limited holding power.

"Hair shine" means a product designed for the primary purpose of creating a shine when applied to the hair. Hair shine includes, but is not limited to, dual-use products designed primarily to impart a sheen to the hair. Hair shine does not include hair spray, hair mousse, hair styling product, hair styling gel, or products whose primary purpose is to condition or hold the hair.

"Hair spray" means a consumer product that is applied to styled hair, and is designed or labeled to provide sufficient rigidity to hold, retain and/or finish the style of the hair for a period of time. Hair spray includes aerosol hair sprays, pump hair sprays, spray waxes; color, glitter, or sparkle hairsprays that make finishing claims; and products that are both a styling and finishing product. Hair spray does not include spray products that are intended to aid in styling but does not provide finishing of a hairstyle. For the purposes of this article, "finish" or "finishing" means the maintaining or holding of previously styled hair for a period of time. For the purposes of this article, "styling" means the forming, sculpting, or manipulating the hair to temporarily alter the hair's shape.

"Hair styling product" means a consumer product that is designed or labeled for the application to wet, damp or dry hair to aid in defining, shaping, lifting, styling and or sculpting of the hair. Hair styling product includes, but is not limited to hair balm; clay; cream; creme; curl straightener; gel; liquid; lotion; paste; pomade; putty; root lifter; serum; spray gel; stick; temporary hair straightener; wax; spray products that aid in styling but do not provide finishing of a hairstyle; and leave-in volumizers, detanglers or conditioners that make styling claims. Hair styling product does not include hair mousse, hair shine, hair spray, or shampoos or conditioners that are rinsed from the hair prior to styling. For the purposes of this article, "finish" or "finishing" means the maintaining or holding of previously styled hair for a period of time. For the purposes of this article, "styling" means the forming, sculpting, or manipulating the hair to temporarily alter the hair's shape.

"Heavy-duty hand cleaner or soap" means a product designed to clean or remove difficult dirt and soils such as oil, grease, grime, tar, shellac, putty, printer's ink, paint, graphite, cement, carbon, asphalt, or adhesives from the hand with or without the use of water. Heavy-duty hand cleaner or soap does not include prescription drug products, antimicrobial hand or body cleaner or soap, astringent or toner, facial cleaner or soap, general-use hand or body cleaner or soap, medicated astringent or medicated toner, or rubbing alcohol.

"Herbicide" means a pesticide product designed to kill or retard a plant's growth, but excludes products that are (i) for agricultural use, or (ii) restricted materials that require a permit for use and possession.

"High volatility organic compound" or "HVOC" means a volatile organic compound that exerts a vapor pressure greater than 80 millimeters of mercury (mm Hg) when measured at 20ºC.

"Household product" means a consumer product that is primarily designed to be used inside or outside of living quarters or residences that are occupied or intended for occupation by people, including the immediate surroundings.

"Insecticide" means a pesticide product that is designed for use against insects or other arthropods, but excluding products that are:

1. For agricultural use;

2. For a use that requires a structural pest control license under applicable state laws or regulations; or

3. Materials classified for restricted use pursuant to 40 CFR 152.75 and require a pesticide business license from the Virginia Pesticide Control Board pursuant to 2VAC20-40-20 for use and possession.

"Insecticide fogger" means an insecticide product designed to release all or most of its content as a fog or mist into indoor areas during a single application.

"Institutional product" or "industrial and institutional (I&I) product" means a consumer product that is designed for use in the maintenance or operation of an establishment that:

1. Manufactures, transports, or sells goods or commodities, or provides services for profit; or

2. Is engaged in the nonprofit promotion of a particular public, educational, or charitable cause.

Establishments include, but are not limited to, government agencies, factories, schools, hospitals, sanitariums, prisons, restaurants, hotels, stores, automobile service and parts centers, health clubs, theaters, or transportation companies. Institutional product does not include household products and products that are incorporated into or used exclusively in the manufacture or construction of the goods or commodities at the site of the establishment.

"Label" means written, printed, or graphic matter affixed to, applied to, attached to, blown into, formed, molded into, embossed on, or appearing upon a consumer product or consumer product package, for purposes of branding, identifying, or giving information with respect to the product or to the contents of the package.

"Laundry prewash" means a product that is designed for application to a fabric prior to laundering and that supplements and contributes to the effectiveness of laundry detergents or provides specialized performance.

"Laundry starch product" means a product that is designed for application to a fabric, either during or after laundering, to impart and prolong a crisp, fresh look and may also act to help ease ironing of the fabric. Laundry starch product includes, but is not limited to, fabric finish, sizing, and starch.

"Lawn and garden insecticide" means an insecticide product labeled primarily to be used in household lawn and garden areas to protect plants from insects or other arthropods. Notwithstanding the requirements of 9VAC5-45-460 C, aerosol lawn and garden insecticides may claim to kill insects or other arthropods.

"Liquid" means a substance or mixture of substances that is capable of a visually detectable flow as determined under ASTM "Standard Test Method for Determining Whether a Material is a Liquid or a Solid" (see 9VAC5-20-21). Liquid does not include powders or other materials that are composed entirely of solid particles.

"Lubricant" means a product designed to reduce friction, heat, noise, or wear between moving parts, or to loosen rusted or immovable parts or mechanisms. Lubricant does not include automotive power steering fluids; products for use inside power generating motors, engines, and turbines, and their associated power-transfer gearboxes; two-cycle oils or other products designed to be added to fuels; products for use on the human body or animals; or products that are:

1. Sold exclusively to establishments that manufacture or construct goods or commodities; and

2. Labeled "not for retail sale."

"LVP content" means the total weight, in pounds, of LVP-VOC in an ACP product multiplied by 100 and divided by the product's total net weight (in pounds, excluding container and packaging), expressed to the nearest 0.1.

"LVP-VOC" means a chemical compound or mixture that contains at least one carbon atom and meets one of the following:

1. Has a vapor pressure less than 0.1 mm Hg at 20ºC, as determined by CARB Method 310 (see 9VAC5-20-21);

2. Is a chemical compound with more than 12 carbon atoms, or a chemical mixture composed solely of compounds with more than 12 carbon atoms as verified by formulation data, and the vapor pressure and boiling point are unknown;

3. Is a chemical compound with a boiling point greater than 216ºC, as determined by CARB Method 310 (see 9VAC5-20-21); or

4. Is the weight percent of a chemical mixture that boils above 216ºC, as determined by CARB Method 310 (see 9VAC5-20-21).

For the purposes of the definition of LVP-VOC, "chemical compound" means a molecule of definite chemical formula and isomeric structure, and "chemical mixture" means a substrate composed of two or more chemical compounds.

"Manufacturer" means a person who imports, manufactures, assembles, produces, packages, repackages, or relabels a consumer product.

"Medicated astringent or medicated toner" means a product regulated as a drug by the United States Food and Drug Administration that is applied to the skin for the purpose of cleaning or tightening pores. Medicated astringent or medicated toner includes, but is not limited to, clarifiers and substrate-impregnated products. Medicated astringent or medicated toner does not include hand, face, or body cleaner or soap products, astringent or toner, cold cream, lotion, antiperspirants, or products that must be purchased with a doctor's prescription.

"Medium volatility organic compound" or "MVOC" means a volatile organic compound that exerts a vapor pressure greater than 2 mm Hg and less than or equal to 80 mm Hg when measured at 20ºC.

"Metal polish or cleanser" means a product designed primarily to improve the appearance of finished metal, metallic, or metallized surfaces by physical or chemical action. To "improve the appearance" means to remove or reduce stains, impurities, or oxidation from surfaces or to make surfaces smooth and shiny. Metal polish or cleanser includes, but is not limited to, metal polishes used on brass, silver, chrome, copper, stainless steel, and other ornamental metals. Metal polish or cleanser does not include automotive wax, polish, sealant, or glaze, wheel cleaner, paint remover or stripper, products designed and labeled exclusively for automotive and marine detailing, or products designed for use in degreasing tanks.

"Missing data days" means the number of days in a compliance period for which the responsible ACP party has failed to provide the required enforceable sales or VOC content data to the board, as specified in the ACP agreement.

"Mist spray adhesive" means an aerosol that is not a special purpose spray adhesive and that delivers a particle or mist spray, resulting in the formation of fine, discrete particles that yield a generally uniform and smooth application of adhesive to the substrate.

"Multipurpose dry lubricant" means a lubricant that is:

1. Designed and labeled to provide lubricity by depositing a thin film of graphite, molybdenum disulfide ("moly"), or polytetrafluoroethylene or closely related fluoropolymer ("teflon") on surfaces; and

2. Designed for general purpose lubrication, or for use in a wide variety of applications.

"Multipurpose lubricant" means a lubricant designed for general purpose lubrication, or for use in a wide variety of applications. Multipurpose lubricant does not include multipurpose dry lubricants, penetrants, or silicone-based multipurpose lubricants.

"Multipurpose solvent" means an organic liquid designed to be used for a variety of purposes, including cleaning or degreasing of a variety of substrates, or thinning, dispersing, or dissolving other organic materials. Multipurpose solvent includes solvents used in institutional facilities, except for laboratory reagents used in analytical, educational, research, scientific, or other laboratories. Multipurpose solvent does not include solvents used in cold cleaners, vapor degreasers, conveyorized degreasers or film cleaning machines, or solvents that are incorporated into, or used exclusively in the manufacture or construction of, the goods or commodities at the site of the establishment.

"Nail polish" means a clear or colored coating designed for application to the fingernails or toenails and including but not limited to, lacquers, enamels, acrylics, base coats, and top coats.

"Nail polish remover" means a product designed to remove nail polish and coatings from fingernails or toenails.

"Nonaerosol product" means a consumer product that is not dispensed by a pressurized spray system.

"Noncarbon containing compound" means a compound that does not contain carbon atoms.

"Nonresilient flooring" means flooring of a mineral content that is not flexible. Nonresilient flooring includes but is not limited to terrazzo, marble, slate, granite, brick, stone, ceramic tile, and concrete.

"Nonselective terrestrial herbicide" means a terrestrial herbicide product that is toxic to plants without regard to species.

"One-product business" means a responsible ACP party that sells, supplies, offers for sale, or manufactures for use in the applicable volatile organic compound emissions control areas designated in 9VAC5-45-400:

1. Only one distinct ACP product, sold under one product brand name, which is subject to the requirements of 9VAC5-45-430; or

2. Only one distinct ACP product line subject to the requirements of 9VAC5-45-430, in which all the ACP products belong to the same product category and the VOC contents in the products are within 98.0% and 102.0% of the arithmetic mean of the VOC contents over the entire product line.

"Oven cleaner" means a cleaning product designed to clean and to remove dried food deposits from oven walls.

"Paint" means a pigmented liquid, liquefiable, or mastic composition designed for application to a substrate in a thin layer that is converted to an opaque solid film after application and is used for protection, decoration or identification, or to serve some functional purpose such as the filling or concealing of surface irregularities or the modification of light and heat radiation characteristics.

"Paint remover or stripper" means a product designed to strip or remove paints or other related coatings, by chemical action, from a substrate without markedly affecting the substrate. Paint remover or stripper does not include multipurpose solvents, paint brush cleaners, products designed and labeled exclusively as graffiti removers, and hand cleaner products that claim to remove paints and other related coatings from skin.

"Penetrant" means a lubricant designed and labeled primarily to loosen metal parts that have bonded together due to rusting, oxidation, or other causes. Penetrant does not include multipurpose lubricants that claim to have penetrating qualities but are not labeled primarily to loosen bonded parts.

"Personal fragrance product" means any product that is applied to the human body or clothing for the primary purpose of adding a scent or masking a malodor, including cologne, perfume, aftershave, and toilet water. Personal fragrance product does not include: (i) deodorant; (ii) medicated products designed primarily to alleviate fungal or bacterial growth on feet or other areas of the body; (iii) mouthwashes, breath fresheners and deodorizers; (iv) lotions, moisturizers, powders or other skin care products used primarily to alleviate skin conditions such as dryness and irritations; (v) products designed exclusively for use on human genitalia; (vi) soaps, shampoos, and products primarily used to clean the human body; and (vii) fragrance products designed to be used exclusively on nonhuman animals.

"Pesticide" means and includes a substance or mixture of substances labeled, designed, or intended for use in preventing, destroying, repelling, or mitigating a pest, or a substance or mixture of substances labeled, designed, or intended for use as a defoliant, desiccant, or plant regulator, provided that the term "pesticide" will not include a substance, mixture of substances, or device that the U.S. Environmental Protection Agency does not consider to be a pesticide.

"Pre-ACP VOC content" means the lowest VOC content of an ACP product between January 1, 1990, and the date on which the application for a proposed ACP is submitted to the board, based on the data obtained from accurate records available to the board that yields the lowest VOC content for the product.

"Pressurized gas duster" means a pressurized product labeled to remove dust from a surface solely by means of mass air or gas flow, including surfaces such as photographs, photographic film negatives, computer keyboards, and other types of surfaces that cannot be cleaned with solvents. Pressurized gas duster does not include dusting aids.

"Principal display panel" means that part of a label that is so designed as to most likely be displayed, presented, shown, or examined under normal and customary conditions of display or purchase. Whenever a principal display panel appears more than once, all requirements pertaining to the principal display panel shall pertain to all such principal display panels.

"Product brand name" means the name of the product exactly as it appears on the principal display panel of the product.

"Product category" means the applicable category that best describes the product as listed in this section and in Table 45-4A in 9VAC5-45-430 A.

"Product form," for the purpose of complying with 9VAC5-45-510 (notification, records and reporting) only, means the applicable form that most accurately describes the product's dispensing form as follows:

A = Aerosol Product.

S = Solid.

P = Pump Spray.

L = Liquid.

SS = Semisolid.

O = Other.

"Product line" means a group of products of identical form and function belonging to the same product category.

"Propellant" means a liquefied or compressed gas that is used in whole or in part, such as a cosolvent, to expel a liquid or other material from the same self-pressurized container or from a separate container.

"Pump spray" means a packaging system in which the product ingredients within the container are not under pressure and in which the product is expelled only while a pumping action is applied to a button, trigger, or other actuator.

"Reconcile" or "reconciliation" means to provide sufficient VOC emission reductions to completely offset shortfalls generated under the ACP during an applicable compliance period.

"Reconciliation of shortfalls plan" means the plan to be implemented by the responsible ACP party when shortfalls have occurred, as approved by the board pursuant to 9VAC5-45-440 B 1 g (10).

"Responsible ACP party" means the company, firm, or establishment that is listed on the ACP product's label. If the label lists two or more companies, firms, or establishments, the responsible ACP party is the party that the ACP product was "manufactured for" or "distributed by," as noted on the label.

"Responsible party" means the company, firm, or establishment that is listed on the product's label. If the label lists two companies, firms, or establishments, the responsible party is the party that the product was "manufactured for" or "distributed by," as noted on the label.

"Restricted materials" means pesticides established as restricted materials under Chapter 39 (§ 3.2-3900 et seq.) of Title 3.2 of the Code of Virginia.

"Retail outlet" means an establishment at which consumer products are sold, supplied, or offered for sale directly to consumers.

"Retailer" means a person who sells, supplies, or offers consumer products for sale directly to consumers.

"Roll-on product" means an antiperspirant or deodorant that dispenses active ingredients by rolling a wetted ball or wetted cylinder on the affected area.

"Rubber and vinyl protectant" means a product designed to protect, preserve, or renew vinyl, rubber, and plastic on vehicles, tires, luggage, furniture, and household products such as vinyl covers, clothing, and accessories. Rubber and vinyl protectant does not include products primarily designed to clean the wheel rim, such as aluminum or magnesium wheel cleaners, and tire cleaners that do not leave an appearance-enhancing or protective substance on the tire.

"Rubbing alcohol" means a product containing isopropyl alcohol (also called isopropanol) or denatured ethanol and labeled for topical use, usually to decrease germs in minor cuts and scrapes, to relieve minor muscle aches, as a rubefacient, and for massage.

"Sealant and caulking compound" means a product with adhesive properties that is designed to fill, seal, waterproof, or weatherproof gaps or joints between two surfaces. Sealant and caulking compound does not include roof cements and roof sealants; insulating foams; removable caulking compounds; clear or paintable or water resistant caulking compounds; floor seam sealers; products designed exclusively for automotive uses; or sealers that are applied as continuous coatings. Sealant and caulking compound also does not include units of product, less packaging, which weigh more than one pound and consist of more than 16 fluid ounces. For the purposes of this definition only, "removable caulking compound" means a compound that temporarily seals windows or doors for three- to six-month time intervals; and "clear or paintable or water resistant caulking compound" means a compound that contains no appreciable level of opaque fillers or pigments, transmits most or all visible light through the caulk when cured, is paintable, and is immediately resistant to precipitation upon application.

"Semisolid" means a product that, at room temperature, will not pour, but will spread or deform easily, including, but not limited to gels, pastes, and greases.

"Shaving cream" means an aerosol product that dispenses a foam lather intended to be used with a blade or cartridge razor or other wet-shaving system, in the removal of facial or other bodily hair. Shaving cream does not include shaving gel.

"Shaving gel" means an aerosol product that dispenses a post-foaming semisolid designed to be used with a blade, cartridge razor, or other shaving system in the removal of facial or other bodily hair. Shaving gel does not include shaving cream.

"Shortfall" means the ACP emissions minus the ACP limit when the ACP emissions were greater than the ACP limit during a specified compliance period, expressed to the nearest pound of VOC. Shortfall does not include emissions occurring prior to the date that the ACP agreement approving an ACP is signed by the board.

"Silicone-based multipurpose lubricant" means a lubricant that is:

1. Designed and labeled to provide lubricity primarily through the use of silicone compounds including, but not limited to, polydimethylsiloxane; and

2. Designed and labeled for general purpose lubrication, or for use in a wide variety of applications.

Silicone-based multipurpose lubricant does not include products designed and labeled exclusively to release manufactured products from molds.

"Single phase aerosol air freshener" means an aerosol air freshener with the liquid contents in a single homogeneous phase and that does not require that the product container be shaken before use.

"Small business" means any stationary source that is owned or operated by a person that employs 100 or fewer individuals; is a small business concern as defined in the federal Small Business Act; is not a major stationary source; does not emit 50 tons or more per year of any regulated pollutant; and emits less than 75 tons per year of all regulated pollutants.

"Solid" means a substance or mixture of substances that, either whole or subdivided (such as the particles composing a powder), is not capable of visually detectable flow as determined under ASTM "Standard Test Method for Determining Whether a Material is a Liquid or a Solid" (see 9VAC5-20-21).

"Special purpose spray adhesive" means an aerosol adhesive that meets any of the following definitions:

1. "Mounting adhesive" means an aerosol adhesive designed to permanently mount photographs, artwork, or other drawn or printed media to a backing (paper, board, cloth, etc.) without causing discoloration to the artwork.

2. "Flexible vinyl adhesive" means an aerosol adhesive designed to bond flexible vinyl to substrates. "Flexible vinyl" means a nonrigid polyvinyl chloride plastic with at least 5.0%, by weight, of plasticizer content. A plasticizer is a material, such as a high boiling point organic solvent, that is incorporated into a plastic to increase its flexibility, workability, or distensibility, and may be determined using ASTM "Standard Practice for Packed Column Gas Chromatography" (see 9VAC5-20-21) or from product formulation data.

3. "Polystyrene foam adhesive" means an aerosol adhesive designed to bond polystyrene foam to substrates.

4. "Automobile headliner adhesive" means an aerosol adhesive designed to bond together layers in motor vehicle headliners.

5. "Polyolefin adhesive" means an aerosol adhesive designed to bond polyolefins to substrates.

6. "Laminate repair or edgebanding adhesive" means an aerosol adhesive designed for:

a. The touch-up or repair of items laminated with high pressure laminates (e.g., lifted edges, delaminates, etc.); or

b. The touch-up, repair, or attachment of edgebonding materials, including but not limited to, other laminates, synthetic marble, veneers, wood molding, and decorative metals.

For the purposes of this definition, "high pressure laminate" means sheet materials that consist of paper, fabric, or other core material that have been laminated at temperatures exceeding 265°F and at pressures between 1,000 and 1,400 psi.

7. "Automotive engine compartment adhesive" means an aerosol adhesive designed for use in motor vehicle under-the-hood applications that require oil and plasticizer resistance, as well as high shear strength, at temperatures of 200-275°F.

"Spot remover" means a product labeled to clean localized areas or remove localized spots or stains on cloth or fabric, such as drapes, carpets, upholstery, and clothing, that does not require subsequent laundering to achieve stain removal. Spot remover does not include dry cleaning fluid, laundry prewash, or multipurpose solvent.

"Spray buff product" means a product designed to restore a worn floor finish in conjunction with a floor buffing machine and special pad.

"Stick product" means an antiperspirant or a deodorant that contains active ingredients in a solid matrix form, and that dispenses the active ingredients by frictional action on the affected area.

"Structural waterproof adhesive" means an adhesive whose bond lines are resistant to conditions of continuous immersion in fresh or salt water and that conforms with the definition in the federal consumer products regulation, 40 CFR 59 Subpart C.

"Surplus reduction" means the ACP limit minus the ACP emissions when the ACP limit was greater than the ACP emissions during a given compliance period, expressed to the nearest pound of VOC. Except as provided in 9VAC5-45-440 F 3, surplus reduction does not include emissions occurring prior to the date that the ACP agreement approving an ACP is signed by the board.

"Surplus trading" means the buying, selling, or transfer of surplus reductions between responsible ACP parties.

"Terrestrial" means to live on or grow from land.

"Tire sealant and inflator" means a pressurized product that is designed to temporarily inflate and seal a leaking tire.

"Toilet/urinal care product" means any product designed or labeled to clean or to deodorize toilet bowls, toilet tanks, or urinals. Toilet bowls, toilet tanks, or urinals includes, but is not limited to, toilets or urinals connected to permanent plumbing in buildings and other structures, portable toilets or urinals placed at temporary or remote locations, and toilet or urinals in vehicles such as buses, recreational motor homes, boats, ships, and aircraft. Toilet/urinal care product does not include bathroom and tile cleaner or general purpose cleaner.

"Total maximum historical emissions" or "TMHE" means the total VOC emissions from all ACP products for which the responsible ACP party has failed to submit the required VOC content or enforceable sales records. The TMHE shall be calculated for each ACP product during each portion of a compliance period for which the responsible ACP party has failed to provide the required VOC content or enforceable sales records. The TMHE shall be expressed to the nearest pound and calculated according to the following calculation:

where:

Highest VOC content = the maximum VOC content that the ACP product has contained in the previous five years, if the responsible ACP party has failed to meet the requirements for reporting VOC content data (for any portion of the compliance period), as specified in the ACP agreement approving the ACP, or the current actual VOC content, if the responsible ACP party has provided all required VOC Content data (for the entire compliance period), as specified in the ACP agreement.

Highest sales = the maximum one-year gross sales of the ACP product in the previous five years, if the responsible ACP party has failed to meet the requirements for reporting enforceable sales records (for any portion of the compliance period), as specified in the ACP agreement approving the ACP, or the current actual one-year enforceable sales for the product, if the responsible ACP party has provided all required enforceable sales records (for the entire compliance period), as specified in the ACP agreement approving the ACP.

Missing data days = (see definition in this section).

1, 2,..., N = each product in an ACP, up to the maximum N, for which the responsible ACP party has failed to submit the required enforceable sales or VOC content data as specified in the ACP agreement.

"Type A propellant" means a compressed gas such as CO₂, N₂, N₂O, or compressed air that is used as a propellant and is either incorporated with the product or contained in a separate chamber within the product's packaging.

"Type B propellant" means a halocarbon that is used as a propellant including chlorofluorocarbons (CFCs), hydrochlorofluorocarbons (HCFCs), and hydrofluorocarbons (HFCs).

"Type C propellant" means a propellant that is not a Type A or Type B propellant, including propane, isobutane, n-butane, and dimethyl ether (also known as dimethyl oxide).

"Undercoating" means an aerosol product designed to impart a protective, nonpaint layer to the undercarriage, trunk interior, or firewall of motor vehicles to prevent the formation of rust or to deaden sound. Undercoating includes, but is not limited to, rubberized, mastic, or asphaltic products.

"Usage directions" means the text or graphics on the product's principal display panel, label, or accompanying literature that describes to the end user how and in what quantity the product is to be used.

"Vinyl/fabric/leather/polycarbonate coating" means a coating designed and labeled exclusively to coat vinyl, fabric, leather, or polycarbonate substrates.

"VOC content" means, except for charcoal lighter products, the total weight of VOC in a product expressed as a percentage of the product weight (exclusive of the container or packaging), as determined pursuant to 9VAC5-45-490 B and C.

For charcoal lighter material products only,

where:

Certified emissions = (see definition in this section).

Certified use rate = (see definition in this section).

"Volatile organic compound" or "VOC" means volatile organic compound as defined in 9VAC5-10-20.

"Wasp and hornet insecticide" means an insecticide product that is designed for use against wasps, hornets, yellow jackets or bees by allowing the user to spray from a distance a directed stream or burst at the intended insects or their hiding place.

"Waterproofer" means a product designed and labeled exclusively to repel water from fabric or leather substrates. Waterproofer does not include fabric protectants.

"Wax" means a material or synthetic thermoplastic substance generally of high molecular weight hydrocarbons or high molecular weight esters of fatty acids or alcohols, except glycerol and high polymers (plastics). Wax includes, but is not limited to, substances derived from the secretions of plants and animals such as carnauba wax and beeswax, substances of a mineral origin such as ozocerite and paraffin, and synthetic polymers such as polyethylene.

"Web spray adhesive" means an aerosol adhesive that is not a mist spray or special purpose spray adhesive.

"Wood cleaner" means a product labeled to clean wooden materials including but not limited to decking, fences, flooring, logs, cabinetry, and furniture. Wood cleaner does not include dusting aids, general purpose cleaners, furniture maintenance products, floor wax strippers, floor polish or waxes, or products designed and labeled exclusively to preserve or color wood.

"Wood floor wax" means wax-based products for use solely on wood floors.

"Working day" means a day between Monday through Friday, inclusive, except for federal holidays.

Historical Notes

Derived from Volume 26, Issue 12, eff. March 17, 2010; amended, Virginia Register Volume 29, Issue 26, eff. October 1, 2013.

Statutory Authority

§ 10.1-1308 of the Code of Virginia.